SHEET A0 // MoonCAD v1SCALE 1:1 · UNITS MM · WCS 0,0
2D 제도 · 3D 솔리드 · DWG / DXF · v1 개발 중

손으로 작도하고, 프롬프트로 지시하고, DWG와 DXF 도면을 바로 여세요.

MoonCAD는 설치 없이 웹 브라우저에서 도면을 그리고 검토할 수 있도록 설계된 CAD 워크스테이션입니다. 익숙한 명령행과 객체 스냅으로 직접 작도하거나, 사람과 같은 명령 엔진을 쓰는 AI 코파일럿에게 평면도와 3D 솔리드 작도를 맡기는 v1 환경을 구축하고 있습니다.

핵심 명령 148개 목표
2D 제도·3D 모델링 (v1)
한 번에 실행 취소
AI가 그린 내용을 한 번에 되돌림
DXF 보존 · DWG 리포트
무수정 DXF 유지 및 DWG 변경 안내
2D 작도 보조선에서 3D 솔리드 형상으로 확장되는 기하학 조형 일러스트
FIG 1.0 // GEOMETRIC CONSTRUCTION2D → 3D SOLID
COMMAND BARIME: KO / EN
> 선분의 시작점을 지정하세요: 0,0
> 다음 끝점을 지정하거나 [직전 취소(U)]: @6000<0
> 호환성 현황 페이지에서 실측 검증 결과를 확인하세요.
SECTION 01 // THREE CORE WORKFLOWS

손으로 그리기, 프롬프트로 지시하기, DWG·DXF 도면 다루기

SHEET A0 · SEC 01
01 // MANUAL DRAFTING

손으로 정밀하게 작도

익숙한 단축 명령어, 정밀한 좌표 입력, 빠른 객체 스냅

LINE, PLINE, TRIM, OFFSET, FILLET, DIMLINEAR 등 실무에서 자주 쓰는 핵심 2D 제도 및 3D 모델링 명령 148개 지원을 v1 목표로 개발하고 있습니다. 한/영 키 상태에 상관없이 물리 키 위치를 인식하므로 한글 입력 중에도 L, C, TR, O 단축키가 바로 실행됩니다.

  • +상대 직교(@x,y), 극좌표(@d<a), 각도 고정(<30), 점 필터(.x, .yz) 입력
  • +끝점·중간점·중심점·교차점·수직점·접점 스냅(F3) 및 직교·극좌표 추적
  • +걸침 창(오른쪽→왼쪽)과 포함 창(왼쪽→오른쪽) 선택 및 정점 신축·이동
명령 예시: LINE 0,0 → @6000<0 → @4000<90 → C
02 // LIVE AI COPILOT

프롬프트로 함께 작도 (v1 목표)

사람과 AI가 같은 명령 엔진을 함께 사용합니다

현재 v1을 목표로 구축 중인 AI 코파일럿은 별도의 그림판이 아니라, 사람이 마우스와 키보드로 쓰는 것과 똑같은 명령 엔진 위에서 도면을 그립니다. 그려지는 과정이 화면에 반투명 미리보기로 먼저 표시된 뒤 도면에 차례로 반영됩니다.

  • +AI가 한 번에 그린 내용은 실행 취소 한 번으로 되돌립니다
  • +사용자가 직접 수정한 객체는 언제나 AI보다 우선하여 그대로 유지됩니다
  • +도면 원본은 브라우저에 머무르며, 개인 API 키는 현재 탭 메모리에만 보관됩니다
프롬프트 예시: "A-WALL 레이어에 가로 6m, 세로 4m 거실 평면도와 900mm 문을 그려줘"
03 // DWG & DXF FILES

DWG 및 DXF 도면 열기·저장

무수정 DXF 보존 및 DWG 변경 리포트 · 호환성 현황 공개

DXF와 DWG 도면을 브라우저에서 열어 레이어, 블록, 치수, 해치 등 2D 요소를 확인하고 편집합니다. DWG에서 가져온 3D 솔리드는 화면에서 확인하고 저장할 때 그대로 유지할 수 있으나 v1에서는 직접 편집할 수 없으며, MoonCAD에서 새로 만든 3D 솔리드는 편집할 수 있습니다.

  • +수정하지 않은 DXF 파일은 원본 그대로 정확히 보존됩니다
  • +DWG 저장은 엔진이 이해하지 못하는 일부 데이터가 빠질 수 있어 무손실이 보장되지 않으며, 저장할 때마다 무엇이 바뀌었는지 리포트합니다
  • +회원가입 없이 브라우저 내부 저장소와 로컬 프로젝트 파일(.mcdz)에 도면을 보관합니다
지원 형식: DXF (무수정 원본 유지) · DWG (저장 시 변경 내역 리포트 제공)
SECTION 02 // COORDINATE INPUT

정밀 좌표 입력 문법 및 한/영 물리 키 인식

명령행은 공백(Space)을 Enter로 처리하며, 직교·극좌표·구면좌표·각도 고정·점 필터 입력을 그대로 지원합니다.

120,80
절대 직교 좌표
현재 사용자 좌표계 원점 (0,0) 기준 X=120, Y=80 위치
@250,-40
상대 직교 좌표
직전 지정점으로부터 가로 250, 세로 -40만큼 이동한 위치
@500<45
상대 극좌표
직전 지정점으로부터 거리 500, 반시계 방향 45° 위치
<30
각도 고정
다음 한 점을 찍을 때 커서 이동 각도를 30° 직선으로 고정
.x / .yz
좌표 성분 필터
한 점의 X값과 다른 점의 YZ값을 조합하여 새 좌표 지정
mtp / from
점 보조 입력
두 점의 정확한 중간점(mtp) 또는 기준점 상대 오프셋(from)
SECTION 03 // AI PRIVACY & SAFETY

도면 기밀 보호 및 안전한 실행

  • 브라우저 내 도면 보관: 원본 도면 파일은 브라우저 밖으로 나가지 않으며, AI 요청 시에는 도면 요약과 필요한 도형 정보만 전송됩니다.
  • 개인 API 키 탭 메모리 보관: 사용자가 입력한 API 키는 현재 브라우저 탭 메모리에만 유지되며 서버 로그에 절대 기록되지 않습니다.
  • 외부 도면 문자 안전 격리: 도면 안의 문자(TEXT·MTEXT)는 명령으로 실행되지 않으며, 기존 도형을 한꺼번에 수정하거나 지울 때는 사용자의 확인을 먼저 거칩니다.
정밀 기하 리본과 원기둥 단면 조형 일러스트
SECTION 04 // FREQUENTLY ASKED QUESTIONS

자주 묻는 질문 (FAQ)

별도 프로그램 설치나 회원가입이 필요한가요?

아니요. MoonCAD는 최신 웹 브라우저에서 설치나 회원가입 없이 실행되도록 설계되었으며, 도면 파일은 사용자의 컴퓨터와 브라우저 내부 저장소에 보관됩니다.

기존 DWG나 DXF 파일을 열고 저장할 수 있나요?

아무것도 수정하지 않은 DXF 파일은 원본 그대로 정확히 보존됩니다. 반면 DWG 저장은 엔진이 이해하지 못하는 일부 데이터가 빠질 수 있어 무손실이 보장되지 않으며, 저장할 때마다 어떤 항목이 바뀌거나 제외되었는지 리포트로 알려줍니다. 형식·버전별 실측 통과 현황은 호환성 현황 페이지에 공개합니다.

한글 키보드 상태에서 단축키가 바로 작동하나요?

네. 도면 문자를 입력하는 단계가 아닐 때는 명령행이 키보드의 물리적 위치와 한글 자모를 함께 인식하므로, 한/영 전환 없이 L(선), C(원), TR(자르기), O(간격 띄우기)를 바로 실행할 수 있습니다.

AI 코파일럿을 쓸 때 도면 보안은 어떻게 유지되나요?

원본 도면 파일 전체는 외부로 전송되지 않으며 사용자의 브라우저에 머무릅니다. 개인 API 키는 현재 탭 메모리에만 유지되어 서버 로그에 기록되지 않으며, 도면 안의 문자는 명령이 아닌 일반 데이터로만 안전하게 처리됩니다.

USER MANUAL // MoonCAD v1KO (9 CH) · EN (9 CH)

MoonCAD 사용 설명서 · User Manual

MoonCAD v1의 목표 사양(핵심 명령 148개 목표, 정밀 좌표 입력 문법, 3D 솔리드 모델링, AI 코파일럿, DXF 및 DWG 파일 처리와 저장 리포트, 알려진 제한 사항)을 한국어와 영어로 안내합니다.

PART I // KOREAN EDITION

한국어 사용 설명서

1. 시작하기

CH 01 · KO
초안 안내: 이 문서는 MoonCAD v1의 목표 사양을 설명합니다. 에디터 화면과 각 명령은 현재 v1 릴리스를 목표로 개발 중이며, 명령별 구현 현황은 상단 메뉴의 호환성 현황 페이지에서 확인할 수 있습니다.

1.1 MoonCAD 개요

MoonCAD는 웹 브라우저에서 동작하도록 설계된 2D 제도 및 3D 솔리드 모델링 도구입니다. 별도의 프로그램 설치 없이 브라우저에서 도면을 작성하고, DWG 및 DXF 파일을 열람·저장하며, 사람과 같은 명령 엔진을 공유하는 AI 코파일럿과 함께 도면을 완성하는 환경을 목표로 합니다.

1.2 화면 구성 (v1 목표)

에디터는 눈의 피로를 줄이는 어두운 도면 시트 작업 환경을 기본으로 하며 다음 영역으로 구성됩니다.

  • •상단 도구모음 및 파일 탭 (RIBBON, FILETAB): 자주 쓰는 작도·수정·3D·치수 아이콘과 현재 도면 탭 표시줄을 전환합니다(v1에서는 브라우저 탭당 하나의 도면을 열며 FILETAB으로 탭 표시줄을 켜고 끕니다).
  • •중앙 작업 캔버스: 2D 및 3D 도면 공간과 십자선 커서, 우측 상단의 방향 큐브(NAVVCUBE), 좌측 하단의 좌표계 아이콘(UCSICON)이 표시됩니다.
  • •좌·우측 도킹 패널: 레이어 관리자(LAYER), 객체 특성(PROPERTIES), 그리고 우측의 AI 코파일럿 패널(MOONAI)을 열고 닫을 수 있습니다.
  • •하단 명령행 (COMMANDLINE) 및 상태 표시줄: 명령어, 옵션 키워드, 좌표를 직접 입력하고 기록을 확인하며, 스냅·격자·직교 모드를 전환합니다.

1.3 기본 마우스 및 키보드 조작

동작객체 선택 / 좌표 지정
실행 방법마우스 왼쪽 클릭
동작포함 창 선택
실행 방법왼쪽에서 오른쪽으로 드래그 (영역 안에 완전히 들어온 객체만 선택)
동작걸침 창 선택
실행 방법오른쪽에서 왼쪽으로 드래그 (영역 경계에 걸친 객체까지 선택)
동작화면 이동 (PAN)
실행 방법마우스 가운데 휠 버튼 누른 채 드래그
동작화면 확대/축소 (ZOOM)
실행 방법마우스 휠 스크롤 (커서 위치 기준)
동작도면 전체 범위 맞춤
실행 방법마우스 휠 버튼 더블클릭 또는 ZOOM → E
동작3D 시점 회전 (3DORBIT)
실행 방법Shift + 마우스 가운데 휠 드래그 또는 3DORBIT 명령
동작직전 명령 반복
실행 방법명령 대기 상태에서 Enter 또는 Space
동작현재 명령 취소 / 선택 해제
실행 방법Esc

1.4 한글 키보드(한/영) 자동 인식

한국어 사용자가 도면을 그릴 때 겪는 한/영 전환 불편을 줄이기 위해, MoonCAD 명령행은 도면 문자 입력(TEXT, MTEXT 내용 입력 등)을 제외한 모든 명령 및 옵션 단계에서 물리 키 위치와 한글 자모를 영문 명령 철자로 자동 변환합니다. 예를 들어 한글 상태에서 ㅣ를 입력하고 Space를 누르면 바로 L(LINE)로 동작합니다.

2. 기본 2D 작도

CH 02 · KO
초안 안내: 이 문서는 MoonCAD v1의 목표 사양을 설명합니다. 각 작도 명령의 구현 현황은 호환성 현황 페이지에 기록됩니다.

2.1 선과 폴리선 그리기

  • •LINE (단축키 L): 시작점과 다음 끝점을 차례로 찍어 개별 선분을 그립니다. 진행 중 U(취소)를 입력하면 직전 선분만 되돌리며, 두 개 이상의 선분을 그린 뒤 C(닫기)를 입력하면 첫 시작점으로 닫습니다. 첫 프롬프트에서 바로 Enter를 누르면 직전에 그린 선이나 호의 끝점에서 이어서 그립니다.
  • •PLINE (단축키 PL): 여러 직선 구간과 호 구간이 하나의 객체로 연결된 2D 폴리선을 그립니다. 진행 중 A로 호 그리기로 전환하거나 W로 시작·끝 선폭을 지정할 수 있습니다.
  • •RECTANG (단축키 REC): 대각선 방향의 두 모서리 점을 찍거나, D(치수) 옵션으로 가로·세로 길이를 입력하여 닫힌 직사각형 폴리선을 만듭니다. F(모깎기) 또는 C(모따기) 값을 미리 지정할 수 있습니다.
  • •POLYGON (단축키 POL): 3변부터 1024변까지의 정다각형을 만듭니다. 중심점 기준(원에 내접 I / 외접 C) 또는 한 변의 양 끝점(E) 방식으로 작도합니다.

2.2 원, 호, 타원 및 스플라인

  • •CIRCLE (단축키 C): 기본 중심점+반지름(또는 D 지름) 방식 외에도 세 점 통과(3P), 지름의 양 끝점(2P), 두 객체에 접하는 반지름(T) 방식을 지원합니다.
  • •ARC (단축키 A): 기본 3점 호, 시작점-중심점-끝점, 중심점-시작점-각도 등 여러 조합으로 원호를 그립니다.
  • •ELLIPSE (단축키 EL): 첫 번째 축의 양 끝점과 반대 축 반경 거리를 지정하거나, 중심점(C) 기준으로 타원 및 타원호를 작성합니다.
  • •SPLINE (단축키 SPL): 지정한 통과점 또는 제어점을 부드럽게 지나는 곡선을 만듭니다.
  • •XLINE (XL) 및 RAY: 도면 전체를 가로지르는 무한 구성선(XLINE: 수평 H, 수직 V, 각도 A, 이등분 B, 간격 O)과 한쪽 방향으로 뻗어 나가는 반직선(RAY)을 보조선으로 활용합니다.

2.3 해치와 주석, 치수 기입

  • •HATCH (단축키 H): 닫힌 영역 안의 한 점을 클릭하거나 경계 객체를 선택하여 해치 패턴(SOLID, ANSI31 등)을 채웁니다.
  • •TEXT (DT) 및 MTEXT (T, MT): 단일 행 문자와 단락 폭·줄간격·글꼴 스타일을 갖춘 다중 행 문자를 기입합니다. 한글 유니코드 및 기존 한글 인코딩 도면 문자를 지원합니다.
  • •치수 명령 (DIMLINEAR, DIMALIGNED, DIMANGULAR, DIMRADIUS, DIMDIAMETER, DIMBASELINE, DIMCONTINUE): 수평·수직·정렬 거리, 두 직선 사이 각도, 원과 호의 반지름·지름 치수를 도면 치수 스타일(DIMSTYLE)에 맞추어 기입합니다.

3. 좌표 입력 및 스냅 문법

CH 03 · KO
초안 안내: 이 문서는 MoonCAD v1의 좌표 입력 및 객체 스냅 목표 사양을 설명합니다.

3.1 좌표계 및 기본 입력 형식

명령행에서는 공백(Space)이 곧 Enter(입력 확정)로 동작하므로, 좌표 숫자 사이에 공백을 넣지 않고 입력합니다.

입력 형태절대 직교 좌표
예시100,200 또는 100,200,50
의미 및 동작현재 사용자 좌표계(UCS) 원점 (0,0,0) 기준 위치
입력 형태상대 직교 좌표
예시@150,-50 또는 @0,0,25
의미 및 동작직전 지정점으로부터의 상대 이동량 (@ 단독 입력은 @0,0,0과 동일)
입력 형태극좌표 (거리<각도)
예시200<45 또는 @120<135
의미 및 동작거리와 XY 평면 각도(도 단위, 반시계 방향 기본)로 지정
입력 형태원통 좌표
예시@100<30,50
의미 및 동작XY 평면 극좌표 거리·각도와 Z축 높이를 함께 지정
입력 형태구면 좌표
예시@100<45<30
의미 및 동작3차원 거리, XY 평면 방위각, XY 평면으로부터의 고도각 지정
입력 형태세계 좌표계(WCS) 강제
예시*0,0,0 또는 @*50,0
의미 및 동작현재 좌표계 회전과 무관하게 표준 세계 좌표계 기준으로 계산
입력 형태직접 거리 입력
예시커서 방향 지정 후 250
의미 및 동작안내선이 가리키는 방향으로 지정한 거리만큼 떨어진 점
입력 형태각도 고정
예시<30
의미 및 동작다음 한 점을 찍을 때 커서 이동 각도를 30도 직선 위로 고정

3.2 점 필터 및 보조 입력

  • •좌표 성분 필터 (.x, .y, .z, .xy, .xz, .yz): 한 객체의 X좌표와 다른 객체의 Y좌표를 조합해 새로운 점을 찍을 때 사용합니다. 예를 들어 .x를 입력하고 첫 점을 찍으면 나머지 YZ 성분을 찍으라는 안내가 이어집니다.
  • •from (기준점 상대 오프셋): 임의의 기준점을 먼저 찍은 뒤, 그 점으로부터 상대 좌표(@50,30)만큼 떨어진 곳을 실제 입력점으로 삼습니다.
  • •mtp / m2p (두 점의 중점): 별도의 보조선을 그리지 않고도 화면에서 찍은 두 점의 정중앙 위치를 계산합니다.
  • •tk / tracking (일시 추적): 수평·수직 방향을 따라 여러 번 꺾어 이동한 최종 위치를 한 점으로 확정합니다.

3.3 객체 스냅 (OSNAP) 및 기능키

상시 스냅(F3)을 켜두거나, 점 입력 단계에서 스냅 약어를 직접 입력해 다음 한 점에만 일시 적용할 수 있습니다.

  • •주요 스냅 키워드: END(끝점), MID(중간점), CEN(중심점), GCE(도형 중심), NOD(점), QUA(사분점), INT(교차점), EXT(연장선), INS(삽입점), PER(수직점), TAN(접점), NEA(근처점), NON(이번 한 점만 스냅 끔).
  • •기능키 요약: F3(객체 스냅), F7(격자 표시), F8(직교 고정), F9(간격 스냅), F10(극좌표 추적 — F8과 상호 전환), F11(객체 스냅 추적), F12(동적 입력).

4. 레이어 및 객체 특성 관리

CH 04 · KO
초안 안내: 이 문서는 MoonCAD v1의 레이어 및 객체 특성 관리 목표 사양을 설명합니다.

4.1 레이어의 역할

복잡한 건축 평면도나 기계 부품도에서 외형선, 중심선, 은선, 치수선, 문자를 구분해 다루려면 레이어(Layer)를 사용합니다. 모든 도면은 삭제하거나 이름을 바꿀 수 없는 기본 레이어 0을 포함합니다.

4.2 레이어 상태 및 속성 (LAYER / -LAYER)

레이어 특성 관리자(LAYER) 또는 명령행 -LAYER 명령에서 각 레이어의 다음 속성을 조절합니다.

  • •켜기 / 끄기 (ON / OFF): 끈 레이어의 객체는 화면에 보이지 않지만 도면 범위 계산에는 남습니다.
  • •동결 / 해동 (Freeze / Thaw): 동결된 레이어는 화면 표시와 스냅·재생성 대상에서 모두 제외되어 큰 도면을 다룰 때 속도를 높여줍니다. 현재 작업 중인 레이어는 동결할 수 없습니다.
  • •잠금 / 잠금 해제 (Lock / Unlock): 잠긴 레이어의 객체는 화면에 보이고 스냅 기준점으로 참조할 수 있으나, 실수로 이동·수정·삭제할 수 없도록 보호됩니다.
  • •색상 (Color), 선종류 (Linetype), 선가중치 (Lineweight): 객체 특성을 ByLayer로 두면 소속 레이어의 색상과 선종류(실선 CONTINUOUS, 중심선, 파선 등), 선 굵기를 그대로 따릅니다.

4.3 국내 실무 레이어 구성 예시

새 도면을 시작하거나 AI 코파일럿에게 작도를 지시할 때 다음과 같은 레이어 구성을 활용할 수 있습니다(일반적인 국내 제도 관행 예시이며 특정 국가 표준 인증을 의미하지 않습니다).

  • •건축 도면 예시: A-WALL(벽체), A-DOOR(문), A-WIND(창호), A-FURN(가구/집기), A-DIMS(치수), A-TEXT(실명/주석), A-HATCH(바닥/단면 해치)
  • •기계 도면 예시: OUTLINE(외형선), HIDDEN(은선), CENTER(중심선), DIMS(치수선), TEXT(주서/공차), HATCH(단면 해치)

4.4 특성 일치 복사 (MATCHPROP)

MATCHPROP(단축키 MA) 명령을 실행하고 기준 객체를 먼저 클릭한 뒤 대상 객체들을 선택하면, 기준 객체의 레이어·색상·선종류·선 굵기 특성을 한 번에 복사해 적용할 수 있습니다.

5. 도형 수정 및 기하 편집 명령

CH 05 · KO
초안 안내: 이 문서는 MoonCAD v1의 도형 수정 및 기하 편집 목표 사양을 설명합니다.

5.1 기본 이동 및 변환 (MOVE, COPY, ROTATE, SCALE, MIRROR)

MoonCAD는 명령 실행 전에 미리 객체를 선택하는 방식과 명령 실행 후 선택하는 방식을 모두 지원합니다.

  • •MOVE (M) / COPY (CO, CP): 기준점과 목표점을 찍어 객체를 이동하거나 복제합니다. 두 번째 점에서 Enter를 누르면 첫 점의 좌표를 그대로 이동 변위로 사용합니다.
  • •ROTATE (RO): 기준점을 중심으로 지정한 각도만큼 회전합니다. C(복사) 옵션으로 원본을 남기거나, R(참조각) 옵션으로 현재 각도를 새 목표 각도에 맞출 수 있습니다.
  • •SCALE (SC): 기준점을 중심으로 크기를 배율만큼 확대·축소합니다. R(참조길이) 옵션을 쓰면 현재 길이를 원하는 수치로 맞출 수 있습니다.
  • •MIRROR (MI): 두 점으로 정의한 대칭축을 기준으로 객체를 대칭 복사하며, 마지막 단계에서 원본 삭제 여부를 선택합니다.

5.2 정밀 기하 편집 (OFFSET, TRIM, EXTEND, FILLET, CHAMFER)

  • •OFFSET (O): 선, 호, 원, 폴리선을 지정한 거리만큼 평행하게 띄워 복제합니다. 닫힌 폴리선을 안쪽이나 바깥쪽으로 간격 띄우기할 때 겹치는 모서리 구간은 기하 규칙에 따라 자동 정리됩니다.
  • •TRIM (TR) 및 EXTEND (EX): 교차하는 경계를 기준으로 선이나 곡선의 불필요한 구간을 잘라내거나(TRIM), 경계선까지 연장합니다(EXTEND). 두 명령 모두 실행 중 Shift 키를 누른 채 클릭하면 반대 동작(TRIM 중에는 연장, EXTEND 중에는 자르기)으로 바로 전환됩니다.
  • •FILLET (F) 및 CHAMFER (CHA): 두 선분이나 호의 모서리를 지정한 반지름의 둥근 원호로 연결(FILLET)하거나 비스듬한 직선으로 모따기(CHAMFER)합니다. 두 번째 객체를 선택할 때 Shift 키를 누르고 클릭하면 설정된 반지름이나 거리값을 바꾸지 않고도 뾰족한 직각 모서리로 즉시 맞닿게 정리합니다.

5.3 분할, 결합, 신축 및 배열 (BREAK, JOIN, STRETCH, ARRAY*)

  • •BREAK (BR) / BREAKATPOINT: 객체의 두 점 사이 구간을 잘라내거나, @를 두 번째 점으로 입력해 간격 없이 한 점에서 두 조각으로 나눕니다. 원을 끊을 때는 첫 점에서 두 번째 점까지 반시계 방향 구간이 제거됩니다.
  • •JOIN (J): 일직선 위의 선분들, 중심과 반지름이 같은 원호들, 또는 끝점이 맞닿은 선·호·폴리선들을 하나의 연속된 폴리선이나 원으로 합칩니다.
  • •STRETCH (S): 반드시 걸침 창(오른쪽에서 왼쪽으로 드래그)으로 선택한 정점들만 이동시키고, 창 바깥의 끝점은 고정하여 도형을 늘이거나 줄입니다.
  • •배열 (ARRAYRECT, ARRAYPOLAR, ARRAYPATH): 행·열 간격의 직사각형 격자 배열, 중심점 기준 원형 배열, 곡선 경로를 따라 일정한 간격으로 배치하는 경로 배열을 지원합니다.

6. 3D 솔리드 모델링

CH 06 · KO
초안 안내: 이 문서는 MoonCAD v1의 3D 솔리드 모델링 목표 사양을 설명합니다.

6.1 기본 3D 솔리드 생성

MoonCAD는 별도 백그라운드 작업 공간에서 3D 솔리드 연산을 수행하여 화면 조작이 멈추지 않도록 설계되었습니다.

  • •BOX: 바닥 직사각형의 두 모서리(또는 중심점 C)와 높이(Z)를 지정하여 직육면체를 만듭니다.
  • •CYLINDER 및 CONE: 바닥면 중심점, 반지름(또는 지름 D), 높이를 입력하여 원기둥과 원뿔(또는 상단 반지름을 가진 원뿔대)을 만듭니다.
  • •SPHERE, PYRAMID, WEDGE, TORUS: 구, 각뿔, 쐐기 블록, 원환체(튜브) 기본 솔리드를 작성합니다.

6.2 단면 기반 3D 형상 생성 (EXTRUDE, REVOLVE, SWEEP, LOFT, PRESSPULL)

  • •EXTRUDE (EXT): 닫힌 2D 폴리선, 원, 영역을 지정한 높이만큼 돌출시켜 솔리드를 만듭니다. 구배 각도나 경로(Path) 옵션을 지원합니다.
  • •REVOLVE (REV): 2D 단면 프로파일을 지정한 축 둘레로 회전(기본 360도)시켜 회전체 솔리드를 만듭니다.
  • •SWEEP 및 LOFT: 단면을 2D/3D 경로 곡선을 따라 쓸어내거나(SWEEP), 둘 이상의 단면 프로파일을 순서대로 이어 붙입니다(LOFT).
  • •PRESSPULL: 닫힌 2D 평면 영역 내부나 솔리드 면을 클릭해 밀거나 당겨 부피를 더하거나 뺍니다.

6.3 솔리드 편집과 외부 DWG 솔리드 제한 사항

  • •MoonCAD에서 만든 솔리드 편집: MoonCAD에서 새로 생성한 솔리드는 합집합(UNION), 차집합(SUBTRACT), 교집합(INTERSECT), 평면 절단(SLICE), 모서리 둥글리기(FILLETEDGE) 및 모따기(CHAMFEREDGE)로 편집할 수 있습니다.
  • •DWG에서 가져온 솔리드 안내: 외부 DWG 파일에서 불러온 기존 3D 솔리드는 화면에서 형상을 확인하고 저장할 때 원본 데이터를 그대로 유지할 수 있지만, v1에서는 부울 연산이나 모서리 가공으로 직접 편집할 수 없습니다.
  • •MASSPROP 및 STLOUT: 솔리드의 부피·표면적·경계 상자를 계산(MASSPROP)하고, 3D 프린팅 등에 쓰이는 STL 메쉬 파일로 내보냅니다(STLOUT).

7. AI 코파일럿 활용 가이드

CH 07 · KO
초안 안내: 이 문서는 현재 개발 중인 MoonCAD v1의 AI 코파일럿 목표 사양과 사용법을 설명합니다.

7.1 사람과 같은 명령 엔진으로 작도

MoonCAD의 AI 코파일럿(MOONAI 명령 또는 우측 AI 패널)은 도면 데이터를 임의로 고치는 별도 경로를 쓰지 않습니다. 모든 AI 작도 작업은 사용자가 마우스와 명령행으로 실행하는 것과 똑같은 명령 엔진을 거쳐 수행됩니다.

  • •실시간 반투명 미리보기: AI가 도면을 생성하는 동안 만들어지는 형상은 화면에 반투명 미리보기로 먼저 나타나며, 검사를 통과한 도형부터 차례대로 도면에 반영됩니다.
  • •실행 취소 한 번으로 되돌리기: AI가 한 번의 지시로 수십 개의 벽체, 문, 치수, 레이어를 그렸더라도, AI가 한 번에 그린 내용은 실행 취소 한 번으로 되돌립니다. Ctrl+Z(U) 또는 패널의 실행 취소 버튼으로 한 번에 원래 상태로 되돌릴 수 있습니다.
  • •중단 옵션: 작도 도중 언제든 멈출 수 있으며, 지금까지 그려진 도형을 남길지 아니면 이번 작업을 모두 취소할지 선택할 수 있습니다.

7.2 효과적인 프롬프트 작성 요령

  • •단위와 치수를 함께 적어주세요: "가로 6m, 세로 4m 거실과 그 오른쪽에 붙은 3m × 4m 침실 평면도를 그려줘"처럼 치수를 적어주면 현재 도면 단위(기본 mm)로 자동 환산(6000, 4000)하여 정확한 좌표로 그립니다.
  • •레이어 이름을 함께 지정하세요: "외벽은 A-WALL 레이어에, 폭 900mm 문은 A-DOOR 레이어에, 전체 치수는 A-DIMS 레이어에 넣어줘"처럼 지시하면 기존 레이어를 쓰거나 새 레이어를 만들어 정리합니다.
  • •선택한 객체 활용: 화면에서 벽체나 도형을 먼저 선택한 뒤 "이 벽에 선형 치수를 달아줘"라고 말하면 현재 선택한 객체를 기준으로 작업합니다.

7.3 수동 편집 우선 및 보안 원칙

  • •사람의 수동 편집이 항상 우선: AI가 작업하는 도중에 사용자가 직접 특정 객체를 수정하거나 편집하고 있으면, AI는 그 객체를 덮어쓰지 않고 사용자의 편집 내용을 그대로 보존합니다.
  • •개인 API 키 관리: 사용자가 직접 입력한 개인 API 키는 현재 브라우저 탭 메모리에만 보관되며, 서버에 저장되거나 로그에 남지 않습니다.
  • •도면 내 악성 지시문 방어: 외부 도면 파일 안의 문자(TEXT, MTEXT)에 적힌 내용은 명령으로 실행되지 않으며, 기존 도형을 한꺼번에 지우거나 수정할 때는 먼저 사용자의 확인을 받습니다.

7.4 대화로 도면 제작 (음성)

AI 패널의 대화로 도면 제작 버튼을 누르면 말로 도면을 그릴 수 있습니다. 음성 대화는 Gemini 3.8 Live가 맡고, 실제 도면은 패널에서 선택한 모델이 그립니다.

  • •작업 설명: 그리는 동안 AI가 지금 어느 부분(벽, 문, 치수, 도면층 등)을 작업하는지 말로 계속 알려 줍니다. 화면에는 지금 하는 일과 대화 내용이 함께 표시됩니다.
  • •말로 방향 바꾸기: 작업 도중에 말을 끼워 넣으면 AI가 하던 말을 멈추고 듣습니다. 방향을 바꾸라는 말이면 지금까지 그린 도형은 유지한 채 의견을 반영해 이어서 그립니다. "멈춰"라고 하면 멈추고, "되돌려"라고 하면 이번 작업에서 그린 것을 되돌립니다.
  • •도면 상태는 선택한 모델이 판단: "지금 문이 몇 개야?", "잘 그려졌어?"처럼 도면 상태를 물으면 Gemini가 짐작하지 않고, 선택한 모델이 실제 도면을 읽기 전용으로 확인한 답을 그대로 읽어 줍니다. 이 확인은 도면을 바꿀 수 없습니다. 그리는 중에는 정확한 확인이 어려워 작업이 끝난 뒤에 확인해 드립니다.
  • •그리는 모델의 질문에 말로 답하기: 그리는 모델이 "문을 열린 상태로 그릴까요, 문틈만 남길까요?"처럼 물으면 AI가 질문과 선택지를 소리 내어 읽어 주고, 말로 대답하면 그대로 전달됩니다. 화면의 버튼을 눌러도 되고, 먼저 한 쪽의 답이 적용됩니다. 확인이 필요한 삭제·대량 변경의 승인은 안전을 위해 음성으로 할 수 없고 화면 버튼으로만 합니다.
  • •같은 안전장치: 음성으로 시작한 작업도 글로 시작한 작업과 같은 명령 엔진, 같은 확인 절차, 같은 한 번의 실행 취소를 씁니다. 대화 중에도 패널의 중지 버튼과 직접 편집이 그대로 동작합니다.
  • •20초 동안 말이 없으면 자동 종료: 아무 말도 하지 않은 채 20초가 지나면 AI가 "필요하실 때 대화로 도면 제작 버튼을 다시 눌러 말씀해 주세요"라고 안내하고 대화를 끝내며 마이크도 꺼집니다. AI가 말하는 중이거나 도면을 그리는 중에는 시간을 세지 않습니다. 그리는 모델의 질문에 대한 대답을 기다릴 때는 시간을 세며, 종료돼도 그 질문은 화면 버튼으로 계속 답할 수 있습니다.
  • •준비물: 마이크와 브라우저의 마이크 권한이 필요합니다. 서버에 Gemini 키가 없으면 패널의 음성용 Gemini 키에 내 키를 넣으세요. 스피커보다 이어폰을 쓰면 AI가 자기 목소리를 듣고 끊기는 일이 줄어듭니다.
  • •개인정보: 음성 대화를 시작하면 마이크 소리와 작업 진행 내용이 Google Gemini로 전송됩니다. 자세한 내용은 AI 코파일럿 개인정보 안내를 확인하세요.

8. 파일 열기, 저장 및 내보내기

CH 08 · KO
초안 안내: 이 문서는 MoonCAD v1의 DXF·DWG 파일 처리 및 출력 목표 사양을 설명합니다.

8.1 지원 파일 형식 개요

MoonCAD는 DWG 및 DXF 도면 파일을 읽고 쓸 수 있으며, 작업 중인 도면을 보관하기 위한 로컬 프로젝트 파일(.mcdz)과 문서·3D 출력용 형식(PDF, SVG, STL, STEP)을 v1 목표로 제공합니다.

파일 형식DXF 도면
확장자.dxf
주요 용도 및 특징수정하지 않은 원본 데이터를 그대로 보존하는 표준 텍스트 CAD 형식
파일 형식DWG 도면
확장자.dwg
주요 용도 및 특징이진 CAD 도면 열람 및 저장 (저장 시 변경·생략 내역 리포트 제공)
파일 형식MoonCAD 프로젝트
확장자.mcdz
주요 용도 및 특징로컬 압축 프로젝트 파일 (도면 및 작업 상태 보관)
파일 형식벡터 문서 출력
확장자.pdf, .svg
주요 용도 및 특징정밀 축척(1:1 등) 인쇄 및 문서 공유용 벡터 출력
파일 형식3D 메쉬 / 솔리드 교환
확장자.stl, .step
주요 용도 및 특징3D 솔리드 모델의 메쉬 출력 및 솔리드 형상 교환

8.2 DXF 원본 보존과 DWG 저장 리포트

  • •DXF 파일: 아무것도 수정하지 않은 DXF 파일은 원본 그대로 정확히 보존됩니다. 일부 객체만 수정하고 저장할 때도 수정하지 않은 레코드와 확장 데이터는 원래 내용을 그대로 유지합니다.
  • •DWG 파일: DWG로 저장할 때는 엔진이 아직 해석하지 못하는 일부 비그래픽 데이터나 속성이 빠질 수 있어 무손실이 보장되지 않습니다. 대신 MoonCAD는 저장할 때마다 무엇이 변경되거나 제외되었는지 리포트로 투명하게 알려주며, 손실 없는 보관이 필요할 때는 DXF 사본을 함께 저장할 수 있습니다.
  • •가져온 3D 솔리드: 외부 DWG 도면에서 가져온 3D 솔리드는 화면에서 확인하고 저장할 때 그대로 유지할 수 있으나, v1에서는 직접 편집할 수 없습니다. 구버전(R13–R2000) DWG의 3D 솔리드는 화면에 그려지지 않지만 저장 시 파일 안에 그대로 유지되며 저장 리포트에 개수가 집계됩니다. MoonCAD에서 새로 만든 3D 솔리드는 편집할 수 있습니다.

8.3 타사 프로그램에서 열 때의 파일 서명 안내에 대하여

일부 상용 CAD 프로그램은 자체 제작 소프트웨어가 아닌 외부 프로그램에서 저장된 DWG 파일을 열 때 비공식 소프트웨어 저장 안내 메시지를 표시합니다. 이는 해당 프로그램의 자체 서명 확인 기능에 따른 현상이며, MoonCAD는 타사의 파일 서명을 위조하지 않습니다.

8.4 로컬 자동 복구 및 오프라인 보관

작업 중인 변경 내역은 브라우저 내부 저장소에 실시간으로 기록되어, 브라우저 탭이 예기치 않게 닫히더라도 다시 열 때 마지막 작업 상태를 복구할 수 있도록 설계되었습니다.

9. 알려진 제한 사항 및 v1 범위

CH 09 · KO
초안 안내: MoonCAD는 실제로 동작하는 범위와 제한 사항을 숨기지 않고 안내합니다. 아래는 v1 릴리스의 범위와 제한 사항입니다.

9.1 v1 설계상 제한 사항 요약

항목DWG 저장 시 일부 데이터 손실 가능성
v1 동작 및 제한 이유수정하지 않은 DXF는 그대로 보존되지만, DWG 저장은 엔진이 이해하지 못하는 일부 데이터가 빠질 수 있어 무손실이 보장되지 않습니다.
안내 방식저장할 때마다 변경 및 생략 내역 리포트를 표시합니다.
항목가져온 3D 솔리드 편집
v1 동작 및 제한 이유외부 DWG에서 가져온 3D 솔리드는 화면에서 보고 저장 시 그대로 유지할 수 있으나 v1에서는 편집할 수 없습니다. 구버전(R13–R2000) 솔리드는 화면에 표시되지 않지만 저장 시 파일 안에 유지되고 리포트에 개수가 표시됩니다. MoonCAD에서 만든 3D 솔리드는 편집 가능합니다.
안내 방식편집 시도 시 안내 메시지가 표시되며, 구버전 솔리드 개수는 저장 리포트에 기록됩니다.
항목다중 지시선(MLEADER) 작성 제외
v1 동작 및 제한 이유MLEADER는 텍스트·블록 내용, 여러 개의 지시선, 스타일 테이블 등 독자적인 복합 서브시스템이 필요하여 v1 작성 명령에서 제외되었습니다. 인출선 주석은 LEADER와 QLEADER를 사용하며, 열람한 파일에 이미 있는 MLEADER와 MULTILEADER 객체는 화면에 표시되고 원본에 보존되어 저장 시 그대로 유지됩니다.
안내 방식호환성 현황 페이지 및 명령 설명서에 안내됩니다.
항목그룹(GROUP) 선택 모드
v1 동작 및 제한 이유그룹 정의를 새로 만드는 별도 명령이 v1 범위에 없으므로 선택 프롬프트에서 G(그룹) 입력 시 UNSUPPORTED 안내를 반환합니다. 단, 열람한 파일의 기존 GROUP 객체는 저장 시 그대로 보존됩니다.
안내 방식선택 중 G 입력 시 명령행에 안내됩니다.
항목치수·해치·배열의 자동 연관성
v1 동작 및 제한 이유새로 작성하는 치수, 해치, 배열은 일반 도형으로 생성되며, 객체 이동 시 치수가 자동으로 따라 움직이지 않습니다.
안내 방식호환성 현황 페이지에 부분 지원(partial)으로 표기됩니다.
항목브라우저 탭당 단일 도면
v1 동작 및 제한 이유한 브라우저 탭에서 하나의 도면을 열며 여러 도면은 브라우저 탭으로 구분합니다. FILETAB 명령은 상단 도면 탭 표시줄을 켜고 끕니다.
안내 방식본 설명서에 명시되어 있습니다.
항목공개 배포 환경의 AI 키 입력
v1 동작 및 제한 이유서버 액세스 토큰이 설정되지 않은 공개 배포 환경에서는 사용자가 설정 창에서 본인 API 키를 직접 입력하여 AI 코파일럿을 사용합니다.
안내 방식AI 패널(MOONAI) 설정에 안내됩니다.
항목.mcdz 재열기 시 실행 취소 기록
v1 동작 및 제한 이유파일 크기를 작게 유지하기 위해 .mcdz 파일을 닫았다가 다시 열면 이전 실행 취소 기록은 초기화됩니다.
안내 방식본 설명서에 명시되어 있습니다.
항목그립(점 끌기) 편집 모드
v1 동작 및 제한 이유정점 신축(Stretch)과 이동(Move) 그립을 지원하며, 회전·축척·대칭은 ROTATE, SCALE, MIRROR 명령을 직접 사용합니다.
안내 방식호환성 현황 페이지에 부분 지원(partial)으로 표기됩니다.
항목동적 입력 툴팁
v1 동작 및 제한 이유커서 옆 툴팁은 기본 꺼짐 상태이며, 하단 명령행에서 모든 좌표 입력 문법이 동작합니다.
안내 방식호환성 현황 페이지에 부분 지원(partial)으로 표기됩니다.
항목브라우저 지원 범위
v1 동작 및 제한 이유Chromium 기반 브라우저(Chrome, Edge 등)를 기준으로 전체 검증을 수행하며, Firefox와 Safari는 기본 동작만 점검합니다.
안내 방식호환성 현황 페이지에 안내됩니다.
항목클라우드 계정 및 실시간 공동 편집
v1 동작 및 제한 이유서버 계정, 클라우드 저장소, 다중 사용자 동시 편집은 포함하지 않으며 모든 파일은 사용자의 브라우저에 머무릅니다.
안내 방식별도 로그인 없이 바로 사용합니다.

9.2 후속 버전으로 미룬 기능

다음 기능들은 v1(핵심 명령 148개 목표) 범위 밖으로 분류되어 후속 버전에서 다룹니다.

  • •파라메트릭 구속조건: 기하·치수 구속 솔버는 v1에 포함되지 않습니다.
  • •동적 블록 작성 및 조건 변경: 동적 블록은 현재 저장된 블록 형상으로 화면에 표시됩니다.
  • •데스크톱 전용 플러그인: 데스크톱 전용 매크로 언어 및 외부 이진 플러그인은 브라우저에서 실행되지 않으며, 표준 명령 스크립트(.scr)를 지원합니다.
  • •외부 참조(XREF), 래스터 이미지 부착, 시트 세트, 점구름: v1에서는 참조 누락 상태를 알리고 원본 정보를 유지합니다.

9.3 파일 형식 검증 및 투명한 공개 원칙

MoonCAD는 지원 파일 형식(DWG, DXF, PDF, SVG, STL, STEP)에 대해 독립적인 파일 검사 도구와 기하 검증 테스트를 통과한 결과만을 기준으로 지원 여부를 판단하며, 각 명령과 도형 요소의 통과·부분 지원·미구현 상태를 호환성 현황 페이지에 있는 그대로 공개합니다.

PART II // ENGLISH EDITION

English User Manual

1. Getting Started

CH 01 · EN
Draft Notice: This chapter describes the intended v1 specification of MoonCAD. The editor and commands are currently in development for v1; check the Compatibility page in the top navigation for live verification status.

1.1 Overview of MoonCAD

MoonCAD is a browser-based 2D drafting and 3D solid modeling application. It is designed to let you draft by hand, direct an AI copilot over the same command engine, and open or save DWG and DXF files with no desktop installation.

1.2 Workspace Layout (v1 Goal)

The editor uses a dark engineering drawing-sheet layout organized into four main zones:

  • •Top Toolbar & Document Tabs (RIBBON, FILETAB): Quick-launch icons for core draw, modify, annotation, dimension, and 3D solid commands, plus the document tab bar (v1 opens one drawing per browser tab and FILETAB toggles the tab strip).
  • •Central Drawing Viewport: Infinite 2D and 3D canvas with crosshair cursor, top-right Orientation Cube (NAVVCUBE), and bottom-left Coordinate System Icon (UCSICON).
  • •Side Dock Panels: Toggleable panels for the Layer Manager (LAYER), Entity Properties (PROPERTIES), and the AI Copilot (MOONAI).
  • •Bottom Command Line (COMMANDLINE) & Status Bar: Direct keyboard entry for commands, options, and coordinates, paired with status toggles for snaps, grid, ortho, and polar tracking.

1.3 Mouse and Keyboard Controls

ActionPick coordinate / Select entity
InputLeft mouse click
ActionEnclosing Window selection
InputDrag left-to-right (selects entities completely inside box)
ActionCrossing Window selection
InputDrag right-to-left (selects entities inside or touching box)
ActionPan view (PAN)
InputMiddle mouse wheel drag
ActionZoom view (ZOOM)
InputScroll mouse wheel (centered at cursor)
ActionZoom to Extents
InputDouble-click middle mouse wheel or type ZOOM → E
Action3D Orbit (3DORBIT)
InputShift + middle mouse drag, or run 3DORBIT
ActionRepeat last command
InputPress Enter or Space at the idle Command prompt
ActionCancel command / Deselect all
InputPress Esc

1.4 Physical Key Recognition Under Korean IME

To prevent accidental Hangul input when typing command aliases, the command bar reads physical key positions (or maps Hangul characters back to QWERTY) whenever a prompt expects a command name, alias, or keyword option rather than free text content. Typing ㅣ (L) or ㅅㄱ (TR) under a Korean IME immediately runs LINE or TRIM.

2. Drawing Basics

CH 02 · EN
Draft Notice: This chapter describes the intended v1 specification of MoonCAD. Live verification status for each command appears on the Compatibility page.

2.1 Lines, Polylines, and Polygons

  • •LINE (L): Pick a start point and consecutive endpoints to create individual line segments. Enter U to undo the last segment, or C after two or more segments to close back to the start point. Pressing Enter at the first prompt continues from the endpoint of the most recently drawn line or arc.
  • •PLINE (PL): Creates a connected 2D polyline composed of straight and circular arc segments. Switch between Arc (A) and Line modes mid-command, or set segment Width (W) and Halfwidth (H).
  • •RECTANG (REC): Pick two opposite corners or use Dimensions (D), Area (A), or Rotation (R) to construct a closed rectangular polyline, with optional Fillet (F) or Chamfer (C) corners.
  • •POLYGON (POL): Generates an equilateral closed polygon with 3 to 1,024 sides, inscribed in (I) or circumscribed about (C) a reference circle, or defined by one edge (E).

2.2 Circles, Arcs, Ellipses, and Splines

  • •CIRCLE (C): Construct circles by center + radius (or Diameter D), 3 points on the circumference (3P), 2 diameter endpoints (2P), or tangent to two objects with a given radius (Ttr).
  • •ARC (A): Draw circular arcs via 3 points, start–center–end, or center–start–end combinations.
  • •ELLIPSE (EL): Define an ellipse by the two endpoints of its first axis and the half-length of its second axis, or start from Center (C).
  • •SPLINE (SPL): Create smooth curves passing through fit points or guided by control vertices (Method).
  • •XLINE (XL) & RAY: Place infinite construction lines (Hor, Ver, Ang, Bisect, Offset) or semi-infinite rays for layout projection.

2.3 Hatches, Text, and Dimensions

  • •HATCH (H): Fill enclosed regions with patterns (SOLID, ANSI31, etc.) by clicking an internal point or selecting bounding entities.
  • •TEXT (DT) & MTEXT (T, MT): Add single-line annotations or formatted multiline text frames with full Unicode and legacy Korean encoding support.
  • •Dimensions (DIMLINEAR, DIMALIGNED, DIMANGULAR, DIMRADIUS, DIMDIAMETER, DIMBASELINE, DIMCONTINUE): Annotate horizontal/vertical distances, aligned lengths, angles, radii, and diameters formatted by the active DIMSTYLE.

3. Coordinate Input and Snaps

CH 03 · EN
Draft Notice: This chapter documents the coordinate input grammar and object snap behavior targeted by MoonCAD v1.

3.1 Coordinate Entry Formats

At the command line, Space acts as Enter (ending a token), so measured coordinates are typed without spaces.

FormatAbsolute Cartesian
Example100,200 or 100,200,50
MeaningExact X, Y, (Z) in the active User Coordinate System (UCS)
FormatRelative Cartesian
Example@150,-50 or @0,0,25
MeaningOffset relative to the last point (@ alone repeats @0,0,0)
FormatPolar (distance<angle)
Example200<45 or @120<135
MeaningDistance and angle in the XY plane (degrees, CCW by default)
FormatCylindrical
Example@100<30,50
MeaningPolar radius and angle in XY plus Z height
FormatSpherical
Example@100<45<30
Meaning3D distance, XY plane angle, and elevation angle from XY
FormatExplicit WCS (*)
Example*0,0,0 or @*50,0
MeaningForces World Coordinate System regardless of active UCS
FormatDirect Distance
ExampleMove cursor, type 250
MeaningPlaces the point at distance 250 along the guide line direction
FormatAngle Override
Example<30
MeaningLocks cursor movement along 30° for the next point

3.2 Point Filters and Modifiers

  • •Coordinate Filters (.x, .y, .z, .xy, .xz, .yz): Combine coordinates from separate picks—for example, type .x and snap to one endpoint to capture its X value, then pick another point to supply YZ.
  • •from: Pick a temporary reference base point first, then enter a relative offset (such as @50,30) from that base.
  • •mtp / m2p: Computes the exact midpoint between any two picked points without drawing construction lines.
  • •tk / tracking: Step through a sequence of orthogonal temporary tracking points and press Enter to commit the final point.

3.3 Object Snaps (OSNAP) and Function Keys

Toggle running object snaps with F3, or type a snap keyword at any point prompt to override for a single pick:

  • •Snap Tokens: END (Endpoint), MID (Midpoint), CEN (Center), GCE (Geometric Center), NOD (Point Node), QUA (Quadrant), INT (Intersection), EXT (Extension), INS (Insertion), PER (Perpendicular), TAN (Tangent), NEA (Nearest), NON (Suppress snaps for this point).
  • •Function Keys: F3 (Object Snap), F7 (Grid), F8 (Ortho Lock), F9 (Increment Snap), F10 (Polar Tracking—mutually exclusive with F8), F11 (Object Snap Tracking), F12 (Dynamic Input).

4. Layers and Object Properties

CH 04 · EN
Draft Notice: This chapter describes the layer table and property management features targeted for MoonCAD v1.

4.1 Organizing Drawings with Layers

Layers separate wall outlines, centerlines, hidden edges, dimensions, and notes so you can control visibility, color, linetype, and lineweight across complex drawings. Every drawing starts with layer 0, which cannot be deleted or renamed.

4.2 Layer States and Attributes (LAYER / -LAYER)

Use the Layer Properties Manager (LAYER) or the command-line -LAYER command to control:

  • •Visible (ON / OFF): Entities on turned-off layers are hidden on screen but remain part of drawing bounds.
  • •Frozen (Freeze / Thaw): Frozen layers are excluded from both display and regeneration to keep large drawings responsive. The active layer cannot be frozen.
  • •Locked (Lock / Unlock): Locked layers remain visible and snappable, but their entities cannot be modified or erased.
  • •Color, Linetype, and Lineweight: Leaving entity properties set to ByLayer ensures entities inherit their layer's visual styling automatically.

4.3 Common Layer Naming Conventions

When starting a new drawing or prompting the AI copilot without pre-existing layers, these common naming patterns keep drawings clean (representing general drafting practice, not a formal KS standard claim):

  • •Architectural: A-WALL (walls), A-DOOR (doors), A-WIND (windows), A-FURN (furniture), A-DIMS (dimensions), A-TEXT (labels), A-HATCH (hatching)
  • •Mechanical: OUTLINE (visible edges), HIDDEN (hidden lines), CENTER (centerlines), DIMS (dimensions), TEXT (notes), HATCH (section hatching)

4.4 Matching Properties (MATCHPROP)

Run MATCHPROP (MA), pick a source entity, and then select one or more target entities to copy the source's layer, color, linetype, and lineweight in one step.

5. Modify and Geometric Editing Commands

CH 05 · EN
Draft Notice: This chapter documents the modify and geometric editing commands targeted for MoonCAD v1.

5.1 Transforms (MOVE, COPY, ROTATE, SCALE, MIRROR)

MoonCAD supports both selecting objects before running a command and selecting objects when prompted inside the command.

  • •MOVE (M) & COPY (CO, CP): Translate or duplicate selected entities from a base point to a target point. Pressing Enter at the second point uses the first point as a relative displacement vector.
  • •ROTATE (RO): Rotate entities around a base pivot by an angle in degrees, with options to keep a Copy (C) or align a Reference (R) angle.
  • •SCALE (SC): Resize entities uniformly from a base point by a scale factor or Reference (R) length.
  • •MIRROR (MI): Reflect entities across a two-point axis and optionally erase or retain the source entities.

5.2 Precision Geometric Edits (OFFSET, TRIM, EXTEND, FILLET, CHAMFER)

  • •OFFSET (O): Create parallel copies of lines, arcs, circles, ellipses, splines, and polylines at a specified distance or through a picked point (Through).
  • •TRIM (TR) & EXTEND (EX): Cut curves back to intersecting cutting edges (TRIM) or project curves forward to boundary edges (EXTEND). Holding Shift while clicking inside either command temporarily flips its mode (TRIM extends; EXTEND trims).
  • •FILLET (F) & CHAMFER (CHA): Connect two curves with a tangent arc of radius R (FILLET) or bevel two straight lines by distances D1, D2 (CHAMFER). Holding Shift on the second pick applies a sharp zero-radius corner without altering the stored radius or chamfer distances.

5.3 Breaking, Joining, Stretching, and Arrays (BREAK, JOIN, STRETCH, ARRAY*)

  • •BREAK (BR) / BREAKATPOINT: Remove a span between two points on an entity, or pass @ (@0,0) as the second point to split an entity cleanly at a single point with zero gap.
  • •JOIN (J): Merge collinear lines, concentric arcs, or contiguous coplanar polylines and arcs into a single curve.
  • •STRETCH (S): Must be selected with a crossing window or crossing polygon (right-to-left drag). Endpoints and vertices inside the crossing box move while exterior vertices stay anchored.
  • •Arrays (ARRAYRECT, ARRAYPOLAR, ARRAYPATH): Distribute copies across a rectangular row/column grid, around a center pivot, or evenly along a path curve.

6. 3D Solid Modeling

CH 06 · EN
Draft Notice: This chapter describes the 3D solid modeling capabilities targeted for MoonCAD v1.

6.1 3D Solid Primitives

MoonCAD runs 3D solid operations in a background worker thread so the viewport stays responsive while modeling.

  • •BOX: Construct a 3D rectangular box from two base corners (or Center C) and a Z height.
  • •CYLINDER & CONE: Specify a base center, radius (or Diameter D), and height (or Top radius for a frustum).
  • •SPHERE, PYRAMID, WEDGE, TORUS: Generate spheres, polygonal pyramids, sloped wedges, and toroidal rings.

6.2 Profile-Based Solid Creation (EXTRUDE, REVOLVE, SWEEP, LOFT, PRESSPULL)

  • •EXTRUDE (EXT): Extrude closed 2D polylines, circles, or planar profiles along +Z or a specified direction vector, path, or taper angle.
  • •REVOLVE (REV): Revolve a 2D profile around an axis line or coordinate axis (X, Y, Z) by a specified angle (default 360°).
  • •SWEEP & LOFT: Sweep a profile along a 2D/3D path curve (SWEEP) or blend across an ordered sequence of cross-section curves (LOFT).
  • •PRESSPULL: Click inside a bounded 2D planar loop or on an existing solid face to add or subtract volume interactively.

6.3 Editing Solids vs. Imported DWG Solids

  • •Solids Created in MoonCAD: Solids created directly in MoonCAD are editable using boolean commands (UNION, SUBTRACT, INTERSECT), planar SLICE, and edge commands (FILLETEDGE, CHAMFEREDGE).
  • •3D Solids Imported from DWG: 3D solids imported from external DWG files can be viewed in the viewport and kept intact when saving, but they are not editable in v1.
  • •MASSPROP & STLOUT: Inspect solid volume, surface area, and bounding box (MASSPROP) or export triangle .stl meshes (STLOUT).

7. AI Copilot Guide

CH 07 · EN
Draft Notice: This chapter describes the AI copilot workflow currently in development for MoonCAD v1.

7.1 Live Drafting on the Shared Command Engine

The MoonCAD AI copilot (MOONAI command or right-side AI panel) has no private backdoor into the drawing. Every AI drawing action executes through the same command engine used by mouse and keyboard commands.

  • •Translucent Previews: While the AI generates geometry, upcoming shapes appear on a translucent preview layer first, and validated elements are added to the drawing progressively.
  • •One Undo Step per Turn: Even if an AI turn creates dozens of walls, doors, dimensions, and layers, everything the AI drew in that turn is grouped together. Press Ctrl+Z (U) or click the undo button in the AI panel to undo the entire turn at once.
  • •Stop & Keep or Undo: Cancel an active turn at any time and choose whether to keep the geometry drawn so far or undo the turn completely.

7.2 Tips for Effective Prompts

  • •State Dimensions and Units Clearly: Prompts such as "Draw a 6m by 4m living room with an adjacent 3m by 4m bedroom to the right" automatically convert meters to drawing units (6000 by 4000 in mm) and connect corners cleanly.
  • •Name Target Layers: Specify layers explicitly—e.g., "Put walls on A-WALL, a 900mm door on A-DOOR, and overall dimensions on A-DIMS"—so the copilot reuses or creates structured layers.
  • •Reference Active Selections: Select entities on the canvas first and say "Dimension this wall on layer A-DIMS" to operate directly on your current selection.

7.3 Human Priority and Security Controls

  • •Manual Edits Always Win: If you modify an object by hand or hold it in an active manual edit while the AI is working, your manual changes always take priority.
  • •Personal API Key: You can enter your own API key in the current browser tab memory. Keys are never stored or logged on our server.
  • •Untrusted File Text Protection: Text inside imported drawings (TEXT, MTEXT, block attributes) is treated strictly as data, never instructions. Deleting existing objects or making bulk edits asks for your confirmation first.

7.4 Draw by Talking (Voice)

Press Draw by talking in the AI panel to draw with your voice. Gemini 3.8 Live does the talking and listening. The model you picked in the panel does the drawing.

  • •It explains the work: While it draws, the AI keeps telling you which part it is on: walls, doors, dimensions, layers. The panel shows what it is doing now, and the conversation, as text.
  • •Change course by speaking: Talk at any point and the AI stops to listen. If you are changing direction, what is already drawn stays and the work carries on with your input. Say "stop" to stop, or ask it to undo to take back what this job drew.
  • •The chosen model judges the drawing: If you ask about the state of the drawing, such as "How many doors are there now?" or "Did that come out right?", Gemini does not guess. The model you picked checks the real drawing in read-only mode and Gemini reads out its answer as it is. That check cannot change the drawing. While drawing is under way an exact check is not possible, so it is done once the work ends.
  • •Answer the drawing model's questions by voice: When the drawing model asks something like "Draw the doors open, or leave an empty gap in the wall?", the AI reads the question and the choices aloud, and your spoken answer is passed on. You can also click a button on the panel; whichever answer comes first applies. For safety, approving a deletion or a bulk change cannot be done by voice, only with the panel button.
  • •Same safeguards: Voice jobs use the same command engine, the same confirmations, and the same single undo as typed ones. The panel's stop buttons and your own edits work during a call.
  • •Ends after 20 seconds of silence: The timer pauses while the AI speaks or a drawing job runs. After activity ends, the conversation and microphone stop if you say nothing for 20 seconds. The timer runs while a drawing question awaits your answer, which can still be given using the panel buttons after the call ends.
  • •What you need: A microphone and the browser's microphone permission. If the server has no Gemini key, enter your own under Gemini key for voice. Headphones keep the AI from hearing itself and cutting off.
  • •Privacy: Once a call starts, your microphone audio and progress notes from the drawing are sent to Google Gemini. See the AI copilot privacy notice for details.

8. Opening and Saving Files

CH 08 · EN
Draft Notice: This chapter describes the DXF and DWG file handling and export features targeted for MoonCAD v1.

8.1 Supported File Formats

MoonCAD reads and writes DWG and DXF drawings, alongside local project files (.mcdz) and vector/mesh export formats.

FormatDXF Drawing
Extension.dxf
PurposeStandard text CAD exchange format with exact preservation of untouched records
FormatDWG Drawing
Extension.dwg
PurposeBinary CAD drawing read and write, with a change report on every save
FormatMoonCAD Archive
Extension.mcdz
PurposeCompact local project file
FormatVector Sheet Output
Extension.pdf, .svg
Purpose1:1 or scaled engineering plots with preserved vector text
Format3D Mesh / Solid Exchange
Extension.stl, .step
PurposeTriangle meshes and 3D solid exchange

8.2 Exact Unedited DXF & Honest DWG Save Reports

  • •DXF Files: An untouched DXF file is preserved as-is when saved. When you edit part of a DXF drawing, unmodified records and extended entity data are kept from the original file.
  • •DWG Files: Saving DWG is not guaranteed lossless and can lose data that the engines do not yet understand. Instead of hiding this, MoonCAD reports what changed or was omitted on each save, and lets you save a companion .dxf copy whenever lossless preservation is required.
  • •Imported 3D Solids: 3D solids imported from DWG files can be viewed and kept when saving, though they are not editable in v1. Older R13–R2000 3D solids are kept in the file on save and counted in the report, but are not drawn on screen. Solids created in MoonCAD are editable.

8.3 About File Signature Notices in Other CAD Programs

Some commercial CAD applications display a notice when opening a DWG file that was last saved by software outside their own product family. MoonCAD does not forge third-party file signatures; we write standard geometry records and report every change on save.

8.4 Local Crash Recovery

Active edits are saved to your browser's local storage so interrupted sessions can be recovered locally when you reopen the editor.

9. Known Limits and v1 Scope

CH 09 · EN
Draft Notice: MoonCAD states its v1 scope and limits plainly.

9.1 v1 Scope Limits

AreaDWG save data loss & save report
v1 Behavior & ReasonAn untouched DXF is preserved as-is, whereas saving DWG is not guaranteed lossless and can lose data the engines do not understand.
How It Appears to UsersEvery DWG save shows a report of what changed or was omitted.
AreaEditing imported 3D solids
v1 Behavior & Reason3D solids imported from DWG can be viewed and kept when saving, but are not editable in v1. Older R13–R2000 3D solids are kept in the file on save and counted in the report, though not drawn on screen. Solids created in MoonCAD are editable.
How It Appears to UsersAttempting to edit an imported solid shows a clear notice; R13–R2000 solid counts appear in the save report.
AreaMultileader (MLEADER) creation
v1 Behavior & ReasonMLEADER is not included as a creation command in v1 because multileaders require their own style table, multi-leader landing/dogleg layout, and block/text content subsystem; use LEADER and QLEADER for leader callouts. Existing MLEADER and MULTILEADER entities in opened files still display, stay in the origin records, and come back on save.
How It Appears to UsersStated on the Compatibility page and command reference.
AreaGroup (GROUP) selection mode
v1 Behavior & ReasonSelecting by group (G) at selection prompts answers UNSUPPORTED in v1 because no group-creation command is in v1 scope; existing GROUP objects in opened files are preserved on save.
How It Appears to UsersReported on the command line when G is entered during selection.
AreaAssociativity for dimensions, hatches, and arrays
v1 Behavior & ReasonNewly created dimensions, hatches, and arrays are plain geometry and do not automatically update when adjacent objects move.
How It Appears to UsersListed as partial on DIM*, HATCH, and ARRAY* on the Compatibility page.
AreaOne document per browser tab
v1 Behavior & Reasonv1 opens one drawing per browser tab; use browser tabs for multiple drawings. FILETAB toggles the top document tab strip.
How It Appears to UsersDocumented here in the user manual.
AreaPersonal API key on public deployments
v1 Behavior & ReasonOn public deployments without a server access token, the AI copilot runs with the user's own API key entered in the settings dialog.
How It Appears to UsersShown in the AI panel (MOONAI) settings.
AreaUndo history across .mcdz reopens
v1 Behavior & ReasonUndo history survives crash recovery within a session, but resets after closing and reopening a .mcdz file to keep files small.
How It Appears to UsersDocumented here in the user manual.
AreaGrip editing modes
v1 Behavior & ReasonStretch and Move grip modes are supported; use ROTATE, SCALE, and MIRROR commands for rotation, scaling, and mirroring.
How It Appears to UsersListed as partial on the Compatibility page.
AreaDynamic input tooltip
v1 Behavior & ReasonThe floating cursor tooltip is off by default; all coordinate entry rules work in the bottom command bar.
How It Appears to UsersListed as partial on the Compatibility page.
AreaBrowser coverage
v1 Behavior & ReasonFull verification runs on Chromium-based browsers; Firefox and Safari receive basic smoke checks.
How It Appears to UsersStated on the Compatibility page.
AreaCloud accounts & real-time collaboration
v1 Behavior & ReasonNo user accounts, cloud storage, or multi-user servers; files remain local on your machine.
How It Appears to UsersZero sign-up required.

9.2 Deferred Beyond v1

The following capabilities lie outside the 148 core commands targeted for v1:

  • •Parametric Constraints: Geometric and dimensional constraint solvers are deferred to a later release.
  • •Dynamic Block Authoring & Evaluation: Dynamic blocks display their stored block representation.
  • •Desktop Plugin Runtimes: Desktop-only macro languages and binary plugins do not run in the browser; standard .scr command scripts are supported.
  • •External References (XREF), Raster Images, Sheet Sets, Point Clouds: v1 reports missing references and keeps underlying records where supported.

9.3 Format Verification & Public Compatibility Page

MoonCAD checks supported file formats (DWG, DXF, PDF, SVG, STL, STEP) with independent file readers and geometry checkers, and publishes the pass, partial, or absent status of each command and entity type on the Compatibility page.

SHEET A0 // GENERATED COMPATIBILITY MATRIXSOURCE: evidence/matrix.json

MoonCAD 호환성 현황 · Compatibility Matrix

VERIFICATION ORACLE DISCLOSURE · 검증 범위 및 판독기 고지

이 저장소와 이 페이지의 어떤 항목도 Autodesk AutoCAD 또는 기타 Autodesk 제품에서 테스트되지 않았습니다(not tested here). 모든 파일·명령·형상 검증은 독립적인 오픈소스 리더와 해석적 오라클(ezdxf 1.4.5, 네이티브 LibreDWG [tests/tools/libredwg, build version not identified] dwg2dxf/dwgread, nasjidwg 0.18.0, @node-projects/acad-ts 3.7.0, OpenCascade occt-wasm 5.11.1 / libcascade 3.1.0, trimesh 5.2.0, pypdf 6.21.4, pdfjs-dist 6.5.438, gltf-validator 2.0.0-dev.3.10)만 사용합니다.

Nothing in this repository or on this page was tested in Autodesk AutoCAD or any other Autodesk product. Every file, command, and geometry check uses independent open-source readers and analytical oracles (ezdxf 1.4.5, native LibreDWG (tests/tools/libredwg, build version not identified) dwg2dxf/dwgread, nasjidwg 0.18.0, @node-projects/acad-ts 3.7.0, OpenCascade occt-wasm 5.11.1 / libcascade 3.1.0, trimesh 5.2.0, pypdf 6.21.4, pdfjs-dist 6.5.438, and gltf-validator 2.0.0-dev.3.10).

실측 요약 · Generated Matrix Summary

148 COMMANDS · 32 ENTITIES · 45 FORMAT ROWS
COMMANDS (148)
passing: 70partial: 68stale: 9absent: 1
ENTITIES (32)
passing: 0partial: 0stale: 26absent: 6
FORMATS (45)
passing: 12partial: 18stale: 9absent / not run: 6

독립 검증 판독기 · Independent Readers Used

DXF (R12–R2018)AutoCAD: not tested here
  • •ezdxf 1.4.5 (Python)
  • •Raw DXF group-code tag differ
ezdxf: 1.4.5 (tests/.venv/Lib/site-packages/ezdxf-1.4.5.dist-info/METADATA)
DWG (R13–R2018)AutoCAD: not tested here
  • •nasjidwg 0.18.0 (in-browser WASM/JS reader & writer)
  • •@node-projects/acad-ts 3.7.0 (independent DWG reader & AC1024/AC1027 writer)
  • •GNU LibreDWG native binaries (tests/tools/libredwg: dwg2dxf & dwgread, build version not identified)
nasjidwg: 0.18.0 (vendor/nasjidwg-0.18.0/package.json)
@node-projects/acad-ts: 3.7.0 (packages/file-dwg/node_modules/@node-projects/acad-ts/package.json)
libredwg: build not identified (tests/tools/libredwg/lib/pkgconfig/libredwg.pc)
3D Solids & Triangle Meshes (STL, OBJ, glTF/GLB, STEP, IGES)AutoCAD: not tested here
  • •occt-wasm 5.11.1 / libcascade 3.1.0 (OpenCascade B-Rep kernel)
  • •trimesh 5.2.0 (Python watertightness & volume oracle for STL/OBJ)
  • •gltf-validator 2.0.0-dev.3.10 (Khronos glTF 2.0 / GLB validator)
  • •STEP & IGES: checked only by the same kernel (occt-wasm 5.11.1)
occt-wasm: 5.11.1 (packages/kernel/node_modules/occt-wasm/package.json)
libcascade: 3.1.0 (packages/kernel-ext/node_modules/libcascade/package.json)
trimesh: 5.2.0 (tests/.venv/Lib/site-packages/trimesh-5.2.0.dist-info/METADATA)
gltf-validator: 2.0.0-dev.3.10 (packages/export/node_modules/gltf-validator/package.json)
Vector PDF Plot & SVGAutoCAD: not tested here
  • •pypdf 6.21.4 (page dimensions & text extraction)
  • •pdfjs-dist 6.5.438 (vector path bounding-box & Hangul glyph run verification)
pypdf: 6.21.4 (tests/.venv/Lib/site-packages/pypdf-6.21.4.dist-info/METADATA)
pdfjs-dist: 6.5.438 (packages/export/node_modules/pdfjs-dist/package.json)

파일 저장 손실 고지 및 교차 검증 결과 · Stated File Losses & Session-Files Evidence

SESSION-FILES EVIDENCE (tests/gates/session-files)
Total scenarios: 74 · Passed: 51 · Failed: 23
DWG STATED LOSSES (packages/file-dwg/NOTES.md)
  • •nasjidwg rewrites from its own in-memory model: layer transparency, layer viewport-freeze flags, MTEXT background fill and flow direction, ByBlock/default lineweights (reset to ByLayer), LEADER dimstyle (reset to Standard), viewport grid/snap/UCS/brightness/visual-style fields, entity thickness, and some DIMSTYLE variables are not kept.
  • •acad-ts does not read LIGHT, PROXY_ENTITY, or ACAD_TABLE (dropped on save in 18 of 156 corpus files, 8 of 71 files at AC1021/AC1024/AC1027); it writes 13 DIMSTYLE variables and only $INSUNITS in the header, and refuses POLYLINE edits that change vertex count.
  • •AC1012 (R13) has no same-generation writer, and AC1021 (R2007) writing is left out by default in offered-targets.json.
  • •Two damaged DWG fuzz inputs that loop inside a single object decoder in vendor/nasjidwg-0.18.0/dist/dwg/objects.js remain non-interruptible mid-object (6 s and 15 s).
DXF STATED LOSSES (packages/file-dxf/NOTES.md)
  • •Edited HATCH entities rewrite from the model and drop DXF groups 71, 97, 330, and 47 (associativity flag, boundary object handles, and pixel size); unedited HATCH records keep their raw tags verbatim.
  • •Edited MESH entities rewrite from the model and drop DXF groups 94, 95, and 140 (edge list and crease weights).
  • •DXF R12 (AC1009) supports only 13 entity types; saving a drawing with modern entity types (LWPOLYLINE, MTEXT, HATCH, ELLIPSE, SPLINE, MESH, 3DSOLID) to AC1009 is blocked.
  • •Characters outside a pre-AC1021 target code page (such as Arabic presentation forms in CP949) are normalized by NFKC or escaped as \U+XXXX.

파일 형식·버전·방향별 검증 표 · Format, Version & Direction (45)

FormatVersionDirectionStatusOracleAutoCADEvidence & Notes
DXFR12 (AC1009)openpassingezdxf 1.4.5 + CP949/UTF-8 decodernot tested here
Reads R12 entities and assigns synthetic handles on open (packages/file-dxf/NOTES.md).
evidence/T14/verify.json
DXFR12 (AC1009)savepartialezdxf 1.4.5 + tests/gates/session-filesnot tested here
Supports 13 R12 entity types; blocks modern types. session-files Scenario 12 (QSAVE on handleless R12 DXF then ERASE) failed with EMPTY_TARGET.
evidence/T13c/first-run.json
DXFR2000 (AC1015)openpassingezdxf 1.4.5 (140 corpus files: 133 ASCII + 7 binary; Hangul CP949/UTF-8)not tested here
Verified across 32 entity entries and 140 DXF corpus files (133 ASCII read + 7 binary in evidence/T20/g5.json).
evidence/T14/verify.json
DXFR2000 (AC1015)savepartialezdxf 1.4.5 + raw tag differ + tests/gates/session-filesnot tested here
Unedited DXF records are preserved byte-for-byte; edited HATCH drops groups 71/97/330/47 and edited MESH drops groups 94/95/140 (packages/file-dxf/NOTES.md). Never marked passing on old G5 numbers alone.
evidence/T13c/first-run.json
DXFR2004 (AC1018)openpassingezdxf 1.4.5 (140 corpus files: 133 ASCII + 7 binary; Hangul CP949/UTF-8)not tested here
Verified across 32 entity entries and 140 DXF corpus files (133 ASCII read + 7 binary in evidence/T20/g5.json).
evidence/T14/verify.json
DXFR2004 (AC1018)savepartialezdxf 1.4.5 + raw tag differ + tests/gates/session-filesnot tested here
Unedited DXF records are preserved byte-for-byte; edited HATCH drops groups 71/97/330/47 and edited MESH drops groups 94/95/140 (packages/file-dxf/NOTES.md). Never marked passing on old G5 numbers alone.
evidence/T13c/first-run.json
DXFR2007 (AC1021)openpassingezdxf 1.4.5 (140 corpus files: 133 ASCII + 7 binary; Hangul CP949/UTF-8)not tested here
Verified across 32 entity entries and 140 DXF corpus files (133 ASCII read + 7 binary in evidence/T20/g5.json).
evidence/T14/verify.json
DXFR2007 (AC1021)savepartialezdxf 1.4.5 + raw tag differ + tests/gates/session-filesnot tested here
Unedited DXF records are preserved byte-for-byte; edited HATCH drops groups 71/97/330/47 and edited MESH drops groups 94/95/140 (packages/file-dxf/NOTES.md). Never marked passing on old G5 numbers alone.
evidence/T13c/first-run.json
DXFR2010 (AC1024)openpassingezdxf 1.4.5 (140 corpus files: 133 ASCII + 7 binary; Hangul CP949/UTF-8)not tested here
Verified across 32 entity entries and 140 DXF corpus files (133 ASCII read + 7 binary in evidence/T20/g5.json).
evidence/T14/verify.json
DXFR2010 (AC1024)savepartialezdxf 1.4.5 + raw tag differ + tests/gates/session-filesnot tested here
Unedited DXF records are preserved byte-for-byte; edited HATCH drops groups 71/97/330/47 and edited MESH drops groups 94/95/140 (packages/file-dxf/NOTES.md). Never marked passing on old G5 numbers alone.
evidence/T13c/first-run.json
DXFR2013 (AC1027)openpassingezdxf 1.4.5 (140 corpus files: 133 ASCII + 7 binary; Hangul CP949/UTF-8)not tested here
Verified across 32 entity entries and 140 DXF corpus files (133 ASCII read + 7 binary in evidence/T20/g5.json).
evidence/T14/verify.json
DXFR2013 (AC1027)savepartialezdxf 1.4.5 + raw tag differ + tests/gates/session-filesnot tested here
Unedited DXF records are preserved byte-for-byte; edited HATCH drops groups 71/97/330/47 and edited MESH drops groups 94/95/140 (packages/file-dxf/NOTES.md). Never marked passing on old G5 numbers alone.
evidence/T13c/first-run.json
DXFR2018 (AC1032)openpassingezdxf 1.4.5 (140 corpus files: 133 ASCII + 7 binary; Hangul CP949/UTF-8)not tested here
Verified across 32 entity entries and 140 DXF corpus files (133 ASCII read + 7 binary in evidence/T20/g5.json).
evidence/T14/verify.json
DXFR2018 (AC1032)savepartialezdxf 1.4.5 + raw tag differ + tests/gates/session-filesnot tested here
Unedited DXF records are preserved byte-for-byte; edited HATCH drops groups 71/97/330/47 and edited MESH drops groups 94/95/140 (packages/file-dxf/NOTES.md). Never marked passing on old G5 numbers alone.
evidence/T13c/first-run.json
DWGR13 (AC1012)openstalenasjidwg 0.18.0 + native LibreDWG (tests/tools/libredwg, build version not identified) (dwgread / dwg2dxf)not tested here
Reads 2D geometry and retains ACIS 3DSOLID records in origin for save reports.
evidence/T20/g6.json
DWGR13 (AC1012)saveabsent (no AC1012 writer; save as DXF or R14/R2000/R2018)offered-targets.json (no AC1012 writer)not tested here
No open-source writer emits AC1012 (R13) DWG containers.
packages/file-dwg/NOTES.md
DWGR14 (AC1014)openstalenasjidwg 0.18.0 + @node-projects/acad-ts 3.7.0 + native LibreDWG (tests/tools/libredwg, build version not identified)not tested here
173 corpus DWG files opened in G6; vendor nasjidwg true-color + transparency word order fix (U8) and damaged-file child-open in session-files remain pending.
evidence/T13c/first-run.json
DWGR14 (AC1014)savepartialnasjidwg 0.18.0 + native LibreDWG (tests/tools/libredwg, build version not identified) (dwg2dxf) + ezdxf 1.4.5 + tests/gates/session-filesnot tested here
Rewritten from nasjidwg model (never verbatim). Drops layer transparency, viewport-freeze, MTEXT background fill, ByBlock lineweight, LEADER dimstyle, and entity thickness (packages/file-dwg/NOTES.md). Never marked passing on old G7 numbers alone.
evidence/T13c/first-run.json
DWGR2000 (AC1015)openstalenasjidwg 0.18.0 + @node-projects/acad-ts 3.7.0 + native LibreDWG (tests/tools/libredwg, build version not identified)not tested here
173 corpus DWG files opened in G6; vendor nasjidwg true-color + transparency word order fix (U8) and damaged-file child-open in session-files remain pending.
evidence/T13c/first-run.json
DWGR2000 (AC1015)savepartialnasjidwg 0.18.0 + native LibreDWG (tests/tools/libredwg, build version not identified) (dwg2dxf) + ezdxf 1.4.5 + tests/gates/session-filesnot tested here
Rewritten from nasjidwg model (never verbatim). Drops layer transparency, viewport-freeze, MTEXT background fill, ByBlock lineweight, LEADER dimstyle, and entity thickness (packages/file-dwg/NOTES.md). Never marked passing on old G7 numbers alone.
evidence/T13c/first-run.json
DWGR2004 (AC1018)openstalenasjidwg 0.18.0 + @node-projects/acad-ts 3.7.0 + native LibreDWG (tests/tools/libredwg, build version not identified)not tested here
173 corpus DWG files opened in G6; vendor nasjidwg true-color + transparency word order fix (U8) and damaged-file child-open in session-files remain pending.
evidence/T13c/first-run.json
DWGR2004 (AC1018)savepartialnasjidwg 0.18.0 + native LibreDWG (tests/tools/libredwg, build version not identified) (dwg2dxf) + ezdxf 1.4.5 + tests/gates/session-filesnot tested here
Rewritten from nasjidwg model (never verbatim). Drops layer transparency, viewport-freeze, MTEXT background fill, ByBlock lineweight, LEADER dimstyle, and entity thickness (packages/file-dwg/NOTES.md). Never marked passing on old G7 numbers alone.
evidence/T13c/first-run.json
DWGR2018 (AC1032)openstalenasjidwg 0.18.0 + @node-projects/acad-ts 3.7.0 + native LibreDWG (tests/tools/libredwg, build version not identified)not tested here
173 corpus DWG files opened in G6; vendor nasjidwg true-color + transparency word order fix (U8) and damaged-file child-open in session-files remain pending.
evidence/T13c/first-run.json
DWGR2018 (AC1032)savepartialnasjidwg 0.18.0 + native LibreDWG (tests/tools/libredwg, build version not identified) (dwg2dxf) + ezdxf 1.4.5 + tests/gates/session-filesnot tested here
Rewritten from nasjidwg model (never verbatim). Drops layer transparency, viewport-freeze, MTEXT background fill, ByBlock lineweight, LEADER dimstyle, and entity thickness (packages/file-dwg/NOTES.md). Never marked passing on old G7 numbers alone.
evidence/T13c/first-run.json
DWGR2007 (AC1021)openstalenasjidwg 0.18.0 + native LibreDWG (tests/tools/libredwg, build version not identified)not tested here
26 AC1021 corpus files opened via nasjidwg 0.18.0.
evidence/T20/g6.json
DWGR2007 (AC1021)saveabsent (left out by default; save as R2018 or DXF)offered-targets.json (AC1021 writer left out by default)not tested here
AC1021 writing is left out by default in offered-targets.json (packages/file-dwg/NOTES.md).
packages/file-dwg/NOTES.md
DWGR2010 (AC1024)openstalenasjidwg 0.18.0 + @node-projects/acad-ts 3.7.0 + native LibreDWG (tests/tools/libredwg, build version not identified)not tested here
Corpus AC1024 files opened and compared against native LibreDWG (tests/tools/libredwg, build version not identified).
evidence/T20/g6.json
DWGR2010 (AC1024)savepartial@node-projects/acad-ts 3.7.0 + native LibreDWG (tests/tools/libredwg, build version not identified) + tests/gates/session-filesnot tested here
Does not read LIGHT, PROXY_ENTITY, or ACAD_TABLE (reported in dropped); writes 13 DIMSTYLE variables and $INSUNITS only (packages/file-dwg/NOTES.md). Scenario 4 in session-files failed in first-run.json.
evidence/T13c/first-run.json
DWGR2013 (AC1027)openstalenasjidwg 0.18.0 + @node-projects/acad-ts 3.7.0 + native LibreDWG (tests/tools/libredwg, build version not identified)not tested here
Corpus AC1027 files opened and compared against native LibreDWG (tests/tools/libredwg, build version not identified).
evidence/T20/g6.json
DWGR2013 (AC1027)savepartial@node-projects/acad-ts 3.7.0 + native LibreDWG (tests/tools/libredwg, build version not identified) + tests/gates/session-filesnot tested here
Does not read LIGHT, PROXY_ENTITY, or ACAD_TABLE (reported in dropped); writes 13 DIMSTYLE variables and $INSUNITS only (packages/file-dwg/NOTES.md). Scenario 4 in session-files failed in first-run.json.
evidence/T13c/first-run.json
DWG -> DXFAny DWG -> R2018 (AC1032) DXFcross-format savepartialezdxf 1.4.5 + tests/gates/session-filesnot tested here
Semantic conversion (never lossless). Offered as dxf-instead fallback when a DWG save is blocked (packages/file-dwg/NOTES.md).
evidence/T13c/first-run.json
DXF -> DWGAny DXF -> R14/R2000/R2004/R2018 DWGcross-format savepartialnasjidwg 0.18.0 + native LibreDWG (tests/tools/libredwg, build version not identified) (dwg2dxf) + tests/gates/session-filesnot tested here
Semantic conversion via nasjidwg; session-files Scenario 9 (DXF -> DWG with Hangul table/entity names) was blocked in first-run.json and patched in T20b U4.
evidence/T13c/first-run.json
.mcdzv1 (OPFS & local archive)open & savestale (T24 verify.json ownedHash changed after T20b session edits)manifest.stateHash + tests/gates/journal/every-byte.test.tsnot tested here
Preserves full DocumentStore state and embedded B-Rep solid blobs; undo stack resets across reopen.
evidence/T24/verify.json
PDF1.7 (ISO A0–A4 vector plot)export (PLOT / EXPORTPDF)passingpypdf 6.21.4 + pdfjs-dist 6.5.438 (page size, vector box error <= 0.1 mm, Hangul text extraction)not tested here
Vector paths + embedded Noto Sans KR subset for Hangul; drops 3D solids, raster images, and optional-content layers (packages/export/NOTES.md).
evidence/T25/g9.json
SVG1.1exportpassingXML element & bounding-box verifier (tests/gates/formats/formats.test.ts)not tested here
2D display snapshot; curves tessellated to polyline segments and 3D solids omitted (packages/export/NOTES.md).
evidence/T25/verify.json
STLBinary & ASCIIexport & import (STLOUT / EXPORT / IMPORT)passingtrimesh 5.2.0 watertight + volume check (tests/gates/g8/check_stl.py & tests/gates/formats)not tested here
Triangle mesh tessellation only; curves, text, layers, and materials are omitted.
evidence/T23/stl-checked.json
OBJWavefront OBJexport & importpassingtrimesh 5.2.0 volume & vertex/face verifier (tests/gates/formats/formats.test.ts)not tested here
Triangle mesh tessellation only; curves, text, layers, and materials are omitted.
evidence/T25/verify.json
glTF / GLB2.0exportpassinggltf-validator 2.0.0-dev.3.10 (0 errors)not tested here
Triangle mesh tessellation only; validated with official Khronos gltf-validator.
evidence/T25/verify.json
STEPAP214 (.step / .stp)exportchecked only by the same kernelocct-wasm 5.11.1 (checked only by the same kernel)not tested here
Exports native B-Rep solids only; volume is checked only by the same kernel (no independent STEP reader in this repo).
evidence/T25/verify.json
IGES5.3 (.iges / .igs)exportchecked only by the same kernelocct-wasm 5.11.1 (checked only by the same kernel)not tested here
Exports native B-Rep solids only; volume is checked only by the same kernel (no independent IGES reader in this repo).
evidence/T25/verify.json
STEP / IGESAP214 / 5.3importabsent in v1 (importFile has no kernel lease)packages/export/NOTES.mdnot tested here
STEP and IGES import requires a kernel lease not passed to importFile in v1; STL and OBJ import are supported.
packages/export/NOTES.md
UI Shells, Panels & Hangul Capturesv1 (1440px & 390px)human visual reviewvisual review: not doneHuman visual inspection sign-offnot tested here
Automated Playwright layout and pixel checks ran; human visual review sign-off is not done yet.
evidence/T15/verify.json
AI Copilot (G10 Mock Streaming)v1 SSE + MockLanguageModelV4prompt-to-drawingabsentFLOW_TABLE monitor + single-step undo + human-edit prioritynot tested here
T32 browser streaming proof over real HTTP/SSE route handler.
AI Copilot (G10 Live Provider)v1 Live Gateway / BYOKlive provider evalnot runtools/ai-live/run.mjs (requires AI_GATEWAY_API_KEY)not tested here
Gated on user-supplied AI_GATEWAY_API_KEY; exits 3 and prints not run when no key is set.
Autodesk AutoCAD (External L4 Kit)All versionsexternal verificationnot tested hereNone in this repositorynot tested here
Nothing was tested in AutoCAD. The generator has no code path that can ever print AutoCAD acceptance as passing.

도형 요소별 검증 표 · Entity Families (32)

EntityGroupDXF (Read / Write)DWG (Read / Write)StatusAutoCADNotes & Evidence
LINEwritepassing / partialstale / partialstalenot tested here
DXF read verified against ezdxf 1.4.5; DXF/DWG save rows gated on tests/gates/session-files (evidence/T13c/first-run.json) and T20b review findings.
evidence/T13c/first-run.json
CIRCLEwritepassing / partialstale / partialstalenot tested here
DXF read verified against ezdxf 1.4.5; DXF/DWG save rows gated on tests/gates/session-files (evidence/T13c/first-run.json) and T20b review findings.
evidence/T13c/first-run.json
ARCwritepassing / partialstale / partialstalenot tested here
DXF read verified against ezdxf 1.4.5; DXF/DWG save rows gated on tests/gates/session-files (evidence/T13c/first-run.json) and T20b review findings.
evidence/T13c/first-run.json
ELLIPSEwritepassing / partialstale / partialstalenot tested here
DXF read verified against ezdxf 1.4.5; DXF/DWG save rows gated on tests/gates/session-files (evidence/T13c/first-run.json) and T20b review findings.
evidence/T13c/first-run.json
POINTwritepassing / partialstale / partialstalenot tested here
DXF read verified against ezdxf 1.4.5; DXF/DWG save rows gated on tests/gates/session-files (evidence/T13c/first-run.json) and T20b review findings.
evidence/T13c/first-run.json
LWPOLYLINEwritepassing / partialstale / partialstalenot tested here
DXF read verified against ezdxf 1.4.5; DXF/DWG save rows gated on tests/gates/session-files (evidence/T13c/first-run.json) and T20b review findings.
evidence/T13c/first-run.json
POLYLINEwritepassing / partialstale / partialstalenot tested here
2D and 3D (with VERTEX and SEQEND). Edited DXF 2D POLYLINE patches vertices in place and preserves widths and xdata.
evidence/T13c/first-run.json
SPLINEwritepassing / partialstale / partialstalenot tested here
DXF read verified against ezdxf 1.4.5; DXF/DWG save rows gated on tests/gates/session-files (evidence/T13c/first-run.json) and T20b review findings.
evidence/T13c/first-run.json
RAYwritepassing / partialstale / partialstalenot tested here
DXF read verified against ezdxf 1.4.5; DXF/DWG save rows gated on tests/gates/session-files (evidence/T13c/first-run.json) and T20b review findings.
evidence/T13c/first-run.json
XLINEwritepassing / partialstale / partialstalenot tested here
DXF read verified against ezdxf 1.4.5; DXF/DWG save rows gated on tests/gates/session-files (evidence/T13c/first-run.json) and T20b review findings.
evidence/T13c/first-run.json
TEXTwritepassing / partialstale / partialstalenot tested here
DXF read verified against ezdxf 1.4.5; DXF/DWG save rows gated on tests/gates/session-files (evidence/T13c/first-run.json) and T20b review findings.
evidence/T13c/first-run.json
MTEXTwritepassing / partialstale / partialstalenot tested here
Hangul Unicode preserved; nasjidwg DWG rewrite drops MTEXT background fill and flow direction.
evidence/T13c/first-run.json
INSERTwritepassing / partialstale / partialstalenot tested here
DXF read verified against ezdxf 1.4.5; DXF/DWG save rows gated on tests/gates/session-files (evidence/T13c/first-run.json) and T20b review findings.
evidence/T13c/first-run.json
ATTDEFwritepassing / partialstale / partialstalenot tested here
Preserved across DXF and DWG after vendor nasjidwg patch (C3/C5); AC1014 corpus QSAVE still shows 32 geometry differences in session-files.
evidence/T13c/first-run.json
ATTRIBwritepassing / partialstale / partialstalenot tested here
Attribute tags, prompts, and edited values preserved across DXF, nasjidwg, and acad-ts (session-files Scenario 7).
evidence/T13c/first-run.json
HATCHwritepassing / partialstale / partialstalenot tested here
Unedited DXF HATCH preserves raw tags; edited DXF HATCH drops groups 71, 97, 330, and 47 (associativity, boundary handles, & pixel size). DWG rewrite normalizes solid hatch scale.
evidence/T13c/first-run.json
DIMENSIONwritepassing / partialstale / partialstalenot tested here
New/edited dimensions generate an anonymous block from DIMSTYLE; associativity is absent in v1 (packages/cmd-dim/partials.json).
evidence/T13c/first-run.json
LEADERwritepassing / partialstale / partialstalenot tested here
Associativity is absent in v1; nasjidwg DWG rewrite resets LEADER dimstyle to Standard.
evidence/T13c/first-run.json
VIEWPORTwritepassing / partialstale / partialstalenot tested here
Paper-space MVIEW clipping and scale supported; nasjidwg DWG rewrite drops viewport grid/snap/UCS/visual-style flags.
evidence/T13c/first-run.json
SOLIDwritepassing / partialstale / partialstalenot tested here
No P0 command creates it. It comes from the entity model and from files.
evidence/T13c/first-run.json
3DFACEwritepassing / partialstale / partialstalenot tested here
No P0 command creates it. It comes from the entity model and from files.
evidence/T13c/first-run.json
MESHwritepassing / partialstale / partialstalenot tested here
AC1024 and later only. Edited DXF MESH drops groups 94, 95, 140 (edge list and crease weights). DWG nasjidwg converts 16 corpus MESH entities to POLYLINE.
evidence/T13c/first-run.json
3DSOLIDwritesAspassing / partialstale / partialstalenot tested here
New B-Rep solids write as MESH + STEP sidecar (AC1024+); unedited ACIS 3DSOLID read from DWG R13–R2018 is preserved by hash in origin.
evidence/T13c/first-run.json
REGIONwritesAspassing / partialstale / partialstalenot tested here
Writes as MESH + STEP sidecar, same as 3DSOLID; unedited REGION read from file stays in origin.
evidence/T13c/first-run.json
MULTILEADERreadAndPreservepassing / absentstale / absentabsentnot tested here
Cut from v1 writing in docs/plan/cuts.json; existing MULTILEADER entities read, display, stay in origin, and come back on save.
docs/plan/cuts.json
BODYreadAndPreservepassing / partialstale / partialstalenot tested here
ACIS payload read from a file is kept in origin by hash; no typed creation command in v1.
evidence/T13c/first-run.json
OPAQUEreadAndPreservepassing / partialstale / partialstalenot tested here
Records with no typed view stay in origin; common properties can change and they can be erased.
evidence/T13c/first-run.json
SURFACEdeferredpassing / absentstale / absentabsentnot tested here
The catalog's `entities` field names these on P0 commands, but v1's EXTRUDE, LOFT, REVOLVE and SWEEP create solids only. Surfaces are deferred in MASTER_PLAN.md section 11.1. One read from a file is preserved like BODY.
evidence/T13c/first-run.json
EXTRUDEDSURFACEdeferredpassing / absentstale / absentabsentnot tested here
The catalog's `entities` field names these on P0 commands, but v1's EXTRUDE, LOFT, REVOLVE and SWEEP create solids only. Surfaces are deferred in MASTER_PLAN.md section 11.1. One read from a file is preserved like BODY.
evidence/T13c/first-run.json
LOFTEDSURFACEdeferredpassing / absentstale / absentabsentnot tested here
The catalog's `entities` field names these on P0 commands, but v1's EXTRUDE, LOFT, REVOLVE and SWEEP create solids only. Surfaces are deferred in MASTER_PLAN.md section 11.1. One read from a file is preserved like BODY.
evidence/T13c/first-run.json
REVOLVEDSURFACEdeferredpassing / absentstale / absentabsentnot tested here
The catalog's `entities` field names these on P0 commands, but v1's EXTRUDE, LOFT, REVOLVE and SWEEP create solids only. Surfaces are deferred in MASTER_PLAN.md section 11.1. One read from a file is preserved like BODY.
evidence/T13c/first-run.json
SWEPTSURFACEdeferredpassing / absentstale / absentabsentnot tested here
The catalog's `entities` field names these on P0 commands, but v1's EXTRUDE, LOFT, REVOLVE and SWEEP create solids only. Surfaces are deferred in MASTER_PLAN.md section 11.1. One read from a file is preserved like BODY.
evidence/T13c/first-run.json

자동 검증 단계 현황 · Verification Gate Status (14)

IDNameStatusAutoCADOracle & Evidence
G1OCCT WASM B-Rep Kernel & Hard Fuzzstale (ownedHash changed)not tested here
Analytical volumes, centroids, bounding boxes, 58 STEP/IGES/BREP corpus files & 560-pair (120 second-boolean) hard fuzz
evidence/L-KERNEL3/verify.json
G22D Computational Geometry & Hit-Testingpassing (T16 & T17 verified)not tested here
Python Shapely 2.2.0 / analytical intersection & offset crosschecks
evidence/T17/verify.json
G3Headless L1 Command Suite (148 P0 Commands & Mutation Kills)154/154 cases passed across 147 active commands (MLEADER cut)not tested here
FLOW_TABLE monitor + undo/redo stateHash + DXF round-trip + 6/6 mutants caught
evidence/g3/l1.json
G4Browser Real-UI Playwright E2E (34 Flows)absent (T31 not finished)not tested here
Real pointer/keyboard input + pixel hit-test + negative control (?fault=no-render-sync)
G5DXF Open & Save Fidelity (140 Corpus Files, R12–R2018)open: passing, save: partial (gated on session-files & T20b)not tested here
ezdxf 1.4.5 + raw group-code tag differ + tests/gates/session-files
evidence/T13c/first-run.json
G6DWG Open Differential (173 Corpus Files, R13–R2018)stale (173 files opened; vendor U8 true-color patch & damaged-file child-open pending)not tested here
nasjidwg 0.18.0 + @node-projects/acad-ts 3.7.0 + native LibreDWG (tests/tools/libredwg, build version not identified)
evidence/T13c/first-run.json
G7DWG Save & Cross-Format Honestypartial (never passing on old G7 comparator alone; gated on session-files & T20b)not tested here
native LibreDWG (tests/tools/libredwg, build version not identified) dwg2dxf + ezdxf 1.4.5 + per-handle geometry/attribute/color signatures + session-files
evidence/T13c/first-run.json
G83D Solid Modeling & Worker Crash Recovery (20 Commands)passing (20/20 solid commands + trimesh 5.2.0 STL)not tested here
Hand-derived volumes, centroids & extrema + trimesh 5.2.0 watertight STL check
evidence/T23/g8.json
G9Vector Plot to PDF & Multi-Format Exportpassing (210x297 mm, boxError 0.000003 mm, Hangul extracted)not tested here
pypdf 6.21.4 + pdfjs-dist 6.5.438 + trimesh 5.2.0 + gltf-validator 2.0.0-dev.3.10
evidence/T25/g9.json
G10-mockAI Copilot Streaming & Tool Contract (Mock Model)absent (T32 not finished)not tested here
MockLanguageModelV4 over SSE + FLOW_TABLE monitor + 1-step undo + negative control
G10-liveAI Copilot Live Gateway Evaluationnot runnot tested here
tools/ai-live/run.mjs (only runs when AI_GATEWAY_API_KEY is supplied)
G11Bilingual User Manual & Legal / Trademark Lintpassing (296 command pages + 18 guide chapters + 0 legal lint violations)not tested here
tools/manual/generate.mjs --check + tools/lint/legal.mjs
evidence/T33a/verify.json
G12Generated Compatibility Matrix & Public Truthpassing (generated from evidence/**, cuts.json, and partials.json)not tested here
tools/matrix/generate.mjs --check + tools/matrix/apply-manual.mjs --check
evidence/matrix.json
AutoCAD-L4Autodesk AutoCAD Verificationnot tested herenot tested here
None — nothing was tested in AutoCAD

명령어 148개 실측 검증 표 · 148 Command Verification Rows

CommandCategoryHeadlessBrowserAutoCADStatusReason & Evidence
MLEADERannotateabsent: L-DXF's writer refuses MULTILEADER (packages/file-dxf/src/capabilities.ts) and no task owns a writer. First on the settled cut list.absentnot tested hereabsent
L-DXF's writer refuses MULTILEADER (packages/file-dxf/src/capabilities.ts) and no task owns a writer. First on the settled cut list.
docs/plan/cuts.json
MTEXTannotateL1 real storeabsent (flow 21)not tested herepartial
Columns is acknowledged and ignored. One MTEXT entity is created. The attach words TL through BR map to attachment points 1 through 9.
packages/cmd-annotate/partials.json
QLEADERannotatepassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-annotate.json
STYLEannotatepassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-annotate.json
TEXTannotateL1 real storeabsent (flow 20)not tested herepartial
TEXT.s0 does not repeat, and Justify and Style have no later point prompt. The point must come before those keywords. After them the insertion point is the last point, which starts at the origin.
packages/cmd-annotate/partials.json
TEXTEDITannotateL1 real storeabsentnot tested herepartial
The only text prompt is under Mode. After a pick the command asks that prompt. A plain string is the new text. The catalog has no text prompt on the pick itself.
packages/cmd-annotate/partials.json
-INSERTblocksL1 real storeabsentnot tested herepartial
The rotation step is the only text-capable step after the scales. Solids and opaque objects have no editable geometry to copy.
packages/cmd-tables/partials.json
ATTDEFblocksL1 real storeabsentnot tested herepartial
The generated flow has a single attribute step. The script used by attribute editing sends six text answers there.
packages/cmd-tables/partials.json
BLOCKblocksL1 real storeabsent (flow 24)not tested herepartial
The document does not refuse an insert cycle by itself. The command checks the block graph first.
packages/cmd-tables/partials.json
EATTEDITblockspassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-tables.json
INSERTblockspassing (L1 real store)absent (flow 24)not tested herepassing
—
evidence/l1/cmd-tables.json
DIMALIGNEDdimensionpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-dim.json
DIMANGULARdimensionpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-dim.json
DIMBASELINEdimensionpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-dim.json
DIMCONTINUEdimensionpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-dim.json
DIMDIAMETERdimensionpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-dim.json
DIMLINEARdimensionpassing (L1 real store)absent (flow 22)not tested herepassing
—
evidence/l1/cmd-dim.json
DIMRADIUSdimensionpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-dim.json
DIMSTYLEdimensionpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-dim.json
3DPOLYdrawpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-draw.json
ARCdrawpassing (L1 real store)absent (flow 05)not tested herepassing
—
evidence/l1/cmd-draw.json
CIRCLEdrawpassing (L1 real store)absent (flow 04)not tested herepassing
—
evidence/l1/cmd-draw.json
DIVIDEdrawpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-draw.json
DONUTdrawpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-draw.json
ELLIPSEdrawpassing (L1 real store)absent (flow 07)not tested herepassing
—
evidence/l1/cmd-draw.json
HATCHdrawL1 real storeabsent (flow 23)not tested herepartial
Associativity is absent in v1 by decision (T17). The HATCH entity stores its loops and pick points as data, and nothing in the document links it back to the objects they came from.
packages/cmd-hatch/partials.json
HATCHEDITdrawL1 real storeabsentnot tested herepartial
There is no associativity in v1, so boundary editing, ASSOCIATE and DISASSOCIATE have nothing to act on. The stored loops are kept whole, so a change of island style takes effect without detecting again.
packages/cmd-hatch/partials.json
LINEdrawpassing (L1 real store)absent (flow 01)not tested herepassing
—
evidence/l1/cmd-draw.json
MEASUREdrawpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-draw.json
PLINEdrawpassing (L1 real store)absent (flow 03)not tested herepassing
—
evidence/l1/cmd-draw.json
POINTdrawpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-draw.json
POLYGONdrawpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-draw.json
RAYdrawpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-draw.json
RECTANGdrawpassing (L1 real store)absent (flow 06)not tested herepassing
—
evidence/l1/cmd-draw.json
SPLINEdrawpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-draw.json
XLINEdrawpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-draw.json
AUDITfilestale (FakeSession): ownedHash changed since verify.json (9cf41d075a91) was recordedabsentnot tested herestale
ownedHash changed since verify.json (9cf41d075a91) was recorded
evidence/T24/verify.json
CLOSEfilestale (FakeSession): ownedHash changed since verify.json (9cf41d075a91) was recordedabsentnot tested herestale
ownedHash changed since verify.json (9cf41d075a91) was recorded
evidence/T24/verify.json
NEWfilestale (FakeSession): ownedHash changed since verify.json (9cf41d075a91) was recordedabsent (flow 31)not tested herestale
ownedHash changed since verify.json (9cf41d075a91) was recorded
evidence/T24/verify.json
OPENfilestale (FakeSession): ownedHash changed since verify.json (9cf41d075a91) was recordedabsent (flow 28)not tested herestale
ownedHash changed since verify.json (9cf41d075a91) was recorded
evidence/T24/verify.json
PURGEfilestale: ownedHash changed since verify.json (9cf41d075a91) was recordedabsentnot tested herestale
ownedHash changed since verify.json (9cf41d075a91) was recorded
evidence/T24/verify.json
QNEWfilestale (FakeSession): ownedHash changed since verify.json (9cf41d075a91) was recordedabsentnot tested herestale
ownedHash changed since verify.json (9cf41d075a91) was recorded
evidence/T24/verify.json
QSAVEfilestale (FakeSession): ownedHash changed since verify.json (9cf41d075a91) was recordedabsent (flow 28)not tested herestale
ownedHash changed since verify.json (9cf41d075a91) was recorded
evidence/T24/verify.json
SAVEASfilestale (FakeSession): ownedHash changed since verify.json (9cf41d075a91) was recordedabsent (flow 29)not tested herestale
ownedHash changed since verify.json (9cf41d075a91) was recorded
evidence/T24/verify.json
STLOUTfilestale (FakeSession): ownedHash changed since verify.json (9cf41d075a91) was recordedabsentnot tested herestale
ownedHash changed since verify.json (9cf41d075a91) was recorded
evidence/T24/verify.json
AREAinquiryL1 real storeabsentnot tested herepartial
Those keywords have no sub-prompts in the flow, so there is nowhere to collect an arc or a running total.
packages/cmd-inquiry/partials.json
DISTinquirypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-inquiry.json
IDinquirypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-inquiry.json
LISTinquirypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-inquiry.json
MASSPROPinquiryL1 real storeabsentnot tested herepartial
Preserved solids are not measured. The flow's Yes/No step asks about a file, and v1 keeps the value on the command result.
packages/cmd-inquiry/partials.json
MEASUREGEOMinquiryL1 real storeabsentnot tested herepartial
The distance branch is the case this package has to satisfy. The other branches need object geometry that is not asked as points.
packages/cmd-inquiry/partials.json
SETVARinquiryL1 real storeabsentnot tested herepartial
The engine's own setter only warns on a read-only name. This command fails the run instead, so a script cannot look successful.
packages/cmd-inquiry/partials.json
-LAYERlayersL1 real storeabsentnot tested herepartial
The generated flow has no sub-prompt for the palette options, and the line-type and line-weight steps do not ask which layers they apply to.
packages/cmd-tables/partials.json
LAYERlayerspartial: headless only (FakeUi)absent (flow 25)not tested herepartial
partial: headless only (FakeUi)
evidence/l1/cmd-tables.json
LAYERCLOSElayerspartial: headless only (FakeUi)absentnot tested herepartial
partial: headless only (FakeUi)
evidence/l1/cmd-tables.json
EXPORTPDFlayoutpartial: headless only (FakeSession)absentnot tested herepartial
partial: headless only (FakeSession)
evidence/l1/cmd-layout.json
LAYOUTlayoutpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-layout.json
MODELlayoutpartial: headless only (FakeView)absentnot tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-layout.json
MSPACElayoutpartial: headless only (FakeView)absentnot tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-layout.json
MVIEWlayoutpartial: headless only (FakeView)absentnot tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-layout.json
PAGESETUPlayoutpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-layout.json
PLOTlayoutpartial: headless only (FakeSession)absent (flow 30)not tested herepartial
partial: headless only (FakeSession)
evidence/l1/cmd-layout.json
PREVIEWlayoutpartial: headless only (FakeSession)absentnot tested herepartial
partial: headless only (FakeSession)
evidence/l1/cmd-layout.json
PSPACElayoutpartial: headless only (FakeView)absentnot tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-layout.json
ARRAYmodifyL1 real storeabsentnot tested herepartial
Associativity needs a dependency graph and an association round trip, and no oracle exists here. New arrays are plain geometry: the copies do not follow later edits to the original, and the command says so. The AI tool text does not call them associative.
packages/cmd-geomedit/partials.json
ARRAYPATHmodifyL1 real storeabsentnot tested herepartial
Associativity needs a dependency graph and an association round trip, and no oracle exists here. New arrays are plain geometry: the copies do not follow later edits to the original, and the command says so. The AI tool text does not call them associative.
packages/cmd-geomedit/partials.json
ARRAYPOLARmodifyL1 real storeabsentnot tested herepartial
Associativity needs a dependency graph and an association round trip, and no oracle exists here. New arrays are plain geometry: the copies do not follow later edits to the original, and the command says so. The AI tool text does not call them associative.
packages/cmd-geomedit/partials.json
ARRAYRECTmodifyL1 real storeabsentnot tested herepartial
Associativity needs a dependency graph and an association round trip, and no oracle exists here. New arrays are plain geometry: the copies do not follow later edits to the original, and the command says so. The AI tool text does not call them associative.
packages/cmd-geomedit/partials.json
BREAKmodifyL1 real storeabsentnot tested herepartial
The commands work on LWPOLYLINE and on the other curve kinds that lie in the UCS XY plane. Anything else is refused by name with a count and left unchanged.
packages/cmd-geomedit/partials.json
BREAKATPOINTmodifypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-geomedit.json
CHAMFERmodifyL1 real storeabsent (flow 17)not tested herepartial
A pick answer carries no modifier key. Use EXTEND, or radius 0 and distance 0, instead.
packages/cmd-geomedit/partials.json
COLORmodifypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-modify.json
COPYmodifypassing (L1 real store)absent (flow 09)not tested herepassing
—
evidence/l1/cmd-modify.json
COPYCLIPmodifypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-modify.json
CUTCLIPmodifypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-modify.json
ERASEmodifypassing (L1 real store)absent (flow 18)not tested herepassing
—
evidence/l1/cmd-modify.json
EXPLODEmodifypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-modify.json
EXTENDmodifyL1 real storeabsent (flow 14)not tested herepartial
A pick answer carries no modifier key. Use EXTEND, or radius 0 and distance 0, instead.
packages/cmd-geomedit/partials.json
FILLETmodifyL1 real storeabsent (flow 16)not tested herepartial
A pick answer carries no modifier key. Use EXTEND, or radius 0 and distance 0, instead.
packages/cmd-geomedit/partials.json
JOINmodifyL1 real storeabsentnot tested herepartial
Lines, arcs, elliptical arcs, polylines and splines of the same family join. Mixed families join as a polyline when they are end to end. 3D polylines and helices are not joined.
packages/cmd-geomedit/partials.json
LENGTHENmodifyL1 real storeabsentnot tested herepartial
The geometry library lengthens lines and circular arcs by an amount, and splines and polylines only by shortening. Dynamic works on lines and arcs. Delta and Total with the Angle option use degrees and apply to arcs.
packages/cmd-geomedit/partials.json
LINETYPEmodifypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-modify.json
LTSCALEmodifypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-modify.json
LWEIGHTmodifypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-modify.json
MATCHPROPmodifypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-modify.json
MIRRORmodifypassing (L1 real store)absent (flow 11)not tested herepassing
—
evidence/l1/cmd-modify.json
MOVEmodifypassing (L1 real store)absent (flow 08)not tested herepassing
—
evidence/l1/cmd-modify.json
OFFSETmodifyL1 real storeabsent (flow 15)not tested herepartial
The commands work on LWPOLYLINE and on the other curve kinds that lie in the UCS XY plane. Anything else is refused by name with a count and left unchanged.
packages/cmd-geomedit/partials.json
PASTECLIPmodifypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-modify.json
PEDITmodifypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-modify.json
PROPERTIESmodifypartial: headless only (FakeUi)absentnot tested herepartial
partial: headless only (FakeUi)
evidence/l1/cmd-modify.json
PROPERTIESCLOSEmodifypartial: headless only (FakeUi)absentnot tested herepartial
partial: headless only (FakeUi)
evidence/l1/cmd-modify.json
REDOmodifypassing (L1 real store)absent (flow 18)not tested herepassing
—
evidence/l1/cmd-modify.json
ROTATEmodifypassing (L1 real store)absent (flow 10)not tested herepassing
—
evidence/l1/cmd-modify.json
SCALEmodifypassing (L1 real store)absent (flow 12)not tested herepassing
—
evidence/l1/cmd-modify.json
STRETCHmodifyL1 real storeabsentnot tested herepartial
io.select does not return the crossing window, so STRETCH reads Crossing and CPolygon itself. Objects selected before the command have no window and move whole (ASSUMED). Text, blocks and points move by their position. Dimensions are refused with a counted message.
packages/cmd-geomedit/partials.json
TRIMmodifyL1 real storeabsent (flow 13)not tested herepartial
A pick answer carries no modifier key. Use EXTEND, or radius 0 and distance 0, instead.
packages/cmd-geomedit/partials.json
Umodifypassing (L1 real store)absent (flow 18)not tested herepassing
—
evidence/l1/cmd-modify.json
UNDOmodifypassing (L1 real store)absent (flow 33)not tested herepassing
—
evidence/l1/cmd-modify.json
QSELECTselectionpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-modify.json
SELECTselectionpassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-modify.json
-OSNAPsettingsL1 real storeabsentnot tested herepartial
The generated step accepted only Enter, so the list is added as text. The bits are the running snap mode.
packages/cmd-view/partials.json
COMMANDLINEsettingspartial: headless only (FakeUi)absentnot tested herepartial
partial: headless only (FakeUi)
evidence/l1/cmd-view.json
DSETTINGSsettingsL1 real storeabsentnot tested herepartial
The panel value is a map of system variables. A name this drawing cannot store must not fail the whole dialog.
packages/cmd-view/partials.json
FILETABsettingspartial: headless only (FakeUi)absentnot tested herepartial
partial: headless only (FakeUi)
evidence/l1/cmd-view.json
GRIDsettingsL1 real storeabsentnot tested herepartial
Those keywords have no sub-prompts, so there is nowhere to take the rest of the option.
packages/cmd-view/partials.json
ORTHOsettingspassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-view.json
OSNAPsettingspassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-view.json
RIBBONsettingspartial: headless only (FakeUi)absentnot tested herepartial
partial: headless only (FakeUi)
evidence/l1/cmd-view.json
SNAPsettingsL1 real storeabsentnot tested herepartial
Those keywords have no sub-prompts, so there is nowhere to take the rest of the option.
packages/cmd-view/partials.json
UNITSsettingspassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-view.json
3DMOVEsolidpassing (L1 + G8 real kernel)absentnot tested herepassing
—
evidence/T23/g8.json
3DROTATEsolidpassing (L1 + G8 real kernel)absentnot tested herepassing
—
evidence/T23/g8.json
BOXsolidpassing (L1 + G8 real kernel)absent (flow 26)not tested herepassing
—
evidence/T23/g8.json
CHAMFEREDGEsolidL1 + G8 real kernelabsentnot tested herepartial
Automatic loop expansion is not implemented.
packages/cmd-solid/partials.json
CONEsolidpassing (L1 + G8 real kernel)absentnot tested herepassing
—
evidence/T23/g8.json
CYLINDERsolidpassing (L1 + G8 real kernel)absentnot tested herepassing
—
evidence/T23/g8.json
EXTRUDEsolidL1 + G8 real kernelabsent (flow 26)not tested herepartial
These profile types need additional exact curve translation.
packages/cmd-solid/partials.json
FILLETEDGEsolidL1 + G8 real kernelabsent (flow 27)not tested herepartial
Automatic tangent chain expansion is not implemented.
packages/cmd-solid/partials.json
INTERSECTsolidpassing (L1 + G8 real kernel)absentnot tested herepassing
—
evidence/T23/g8.json
LOFTsolidL1 + G8 real kernelabsentnot tested herepartial
The basic recipe is measured analytically. Guide matching and smooth surface control need a separate command flow and oracle.
packages/cmd-solid/partials.json
PRESSPULLsolidL1 + G8 real kernelabsentnot tested herepartial
Region detection and constrained neighboring faces have no accepted command-layer recipe.
packages/cmd-solid/partials.json
PYRAMIDsolidpassing (L1 + G8 real kernel)absentnot tested herepassing
—
evidence/T23/g8.json
REVOLVEsolidpassing (L1 + G8 real kernel)absentnot tested herepassing
—
evidence/T23/g8.json
SLICEsolidL1 + G8 real kernelabsentnot tested herepartial
The command currently collects an explicit cutting plane.
packages/cmd-solid/partials.json
SPHEREsolidpassing (L1 + G8 real kernel)absentnot tested herepassing
—
evidence/T23/g8.json
SUBTRACTsolidpassing (L1 + G8 real kernel)absent (flow 26)not tested herepassing
—
evidence/T23/g8.json
SWEEPsolidL1 + G8 real kernelabsentnot tested herepartial
Additional placement controls require their own verified recipes.
packages/cmd-solid/partials.json
TORUSsolidL1 + G8 real kernelabsentnot tested herepartial
The raw kernel can report a valid spindle with incorrect volume; the command refuses this case.
packages/cmd-solid/partials.json
UNIONsolidpassing (L1 + G8 real kernel)absentnot tested herepassing
—
evidence/T23/g8.json
WEDGEsolidpassing (L1 + G8 real kernel)absentnot tested herepassing
—
evidence/T23/g8.json
HELPutilitypartial: headless only (FakeUi)absentnot tested herepartial
partial: headless only (FakeUi)
evidence/l1/cmd-inquiry.json
MOONAIutilitypartial: headless only (FakeUi)absentnot tested herepartial
partial: headless only (FakeUi)
evidence/l1/cmd-inquiry.json
MULTIPLEutilityL1 real storeabsentnot tested herepartial
A non-interactive run has no Escape to end the repeat, and a dialog does not repeat.
packages/cmd-inquiry/partials.json
SCRIPTutilitypassing (L1 real store)absentnot tested herepassing
—
evidence/l1/cmd-inquiry.json
3DORBITviewpartial: headless only (FakeView)absent (flow 27)not tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-view.json
NAVVCUBEviewpartial: headless only (FakeUi)absentnot tested herepartial
partial: headless only (FakeUi)
evidence/l1/cmd-view.json
PANviewpartial: headless only (FakeView)absentnot tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-view.json
PLANviewpartial: headless only (FakeView)absentnot tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-view.json
REDRAWviewpartial: headless only (FakeView)absentnot tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-view.json
REDRAWALLviewpartial: headless only (FakeView)absentnot tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-view.json
REGENviewpartial: headless only (FakeView)absentnot tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-view.json
REGENALLviewpartial: headless only (FakeView)absentnot tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-view.json
UCSviewL1 real storeabsentnot tested herepartial
The face and object steps have no later prompt that can build a frame. The named branch has no prompt for the name. The previous list is not a document record.
packages/cmd-view/partials.json
UCSICONviewpartial: headless only (FakeUi)absentnot tested herepartial
partial: headless only (FakeUi)
evidence/l1/cmd-view.json
ZOOMviewpartial: headless only (FakeView)absent (flow 19)not tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-view.json
HIDEvisualpartial: headless only (FakeView)absent (flow 27)not tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-view.json
VSCURRENTvisualpartial: headless only (FakeView)absentnot tested herepartial
partial: headless only (FakeView)
evidence/l1/cmd-view.json
SHEET N-01 // LEGAL NOTICES & OPEN-SOURCE ATTRIBUTIONKO · EN

MoonCAD 법적 고지 및 오픈소스 라이선스 · Legal Notices & Open-Source Licenses

이 페이지는 MoonCAD에 포함된 오픈소스 소프트웨어 라이선스 고지, LGPL-2.1 기반 WebAssembly 모듈(/wasm/occt-wasm.wasm) 교체 안내, 상표권 귀속 고지, 그리고 외부 CAD 프로그램의 타사 저장 파일 안내에 관한 설명을 한국어와 영어로 제공합니다.

This page provides third-party open-source software attributions, LGPL-2.1 notices and replacement instructions for /wasm/occt-wasm.wasm, trademark attributions, and a plain explanation of third-party file-origin warnings in both Korean and English.

SECTION 01 // LGPL-2.1 DYNAMIC MODULE & REPLACEMENT

LGPL-2.1 고지 및 /wasm/occt-wasm.wasm 교체 방법 · LGPL-2.1 Notice & Replacing /wasm/occt-wasm.wasm

한국어 안내 (KOREAN)

MoonCAD의 3D 솔리드 커널 워커는 GNU 약소 일반 공중 사용 허가서 버전 2.1(LGPL-2.1)에 따라 배포되는 occt-wasm (5.11.1) 및 libcascade (3.1.0)를 사용합니다. 이 커널은 애플리케이션 본체에 정적으로 결합되지 않고, 런타임에 별도의 정적 파일 경로인 /wasm/occt-wasm.wasm에서 WebAssembly 모듈로 동적 로드됩니다.

사용자가 직접 수정·빌드한 /wasm/occt-wasm.wasm으로 교체하는 방법:
  1. 호환되는 LGPL-2.1 소스(occt-wasm / libcascade)를 수정한 뒤 동일한 C ABI 심볼을 내보내는 occt-wasm.wasm 바이너리로 컴파일합니다.
  2. 웹 서버 또는 로컬 배포 디렉터리의 apps/web/public/wasm/occt-wasm.wasm(서비스 경로 /wasm/occt-wasm.wasm) 파일을 새 바이너리로 덮어쓰고, /wasm/manifest.json의 sha256 및 size 값을 갱신합니다.
  3. 또는 워커 부트 설정에서 kernelWasmUrl에 사용자 지정 .wasm URL을 전달하면 애플리케이션 재빌드 없이 수정된 LGPL 모듈이 즉시 로드됩니다.
ENGLISH NOTICE

The 3D solid modeling worker in MoonCAD uses occt-wasm (5.11.1) and libcascade (3.1.0), which are licensed under the GNU Lesser General Public License version 2.1 (LGPL-2.1). Rather than linking the kernel statically into the main bundle, MoonCAD loads it dynamically at runtime from the standalone WebAssembly asset /wasm/occt-wasm.wasm.

How to replace /wasm/occt-wasm.wasm with a modified build:
  1. Build a compatible occt-wasm.wasm binary from modified occt-wasm / libcascade source code preserving the exported C ABI functions.
  2. Replace apps/web/public/wasm/occt-wasm.wasm (served at /wasm/occt-wasm.wasm) and update the sha256 and size fields in /wasm/manifest.json.
  3. Alternatively, pass a custom kernelWasmUrl to the kernel worker configuration at boot to load your replacement WebAssembly module without rebuilding the web application.
SECTION 02 // TRADEMARK ATTRIBUTION

상표권 귀속 고지 · Trademark Attribution

한국어 (KO)

DWG는 Autodesk AutoCAD® 소프트웨어의 기본 파일 형식이자 Autodesk, Inc.의 상표입니다. AutoCAD와 Autodesk는 Autodesk, Inc.의 등록 상표입니다. MoonCAD는 독립 제품이며 Autodesk, Inc.와 제휴, 후원 또는 보증 관계가 없습니다.

ENGLISH (EN)

DWG is the native file format for Autodesk's AutoCAD® software and is a trademark of Autodesk, Inc. AutoCAD and Autodesk are registered trademarks of Autodesk, Inc. MoonCAD is an independent product and is not affiliated with, sponsored by, or endorsed by Autodesk, Inc.

SECTION 03 // THIRD-PARTY FILE-ORIGIN WARNING EXPLANATION

타사 저장 파일 출처 알림에 대한 안내 · Third-Party File-Origin Warning Explanation

한국어 설명 (KO)

일부 상용 CAD 프로그램은 자체 제품군 외부의 소프트웨어에서 마지막으로 저장된 DWG 파일을 열 때 타사 저장 파일 안내 창을 표시합니다.

이 알림은 파일이 손상되었다는 뜻이 아니라, 해당 상용 CAD 프로그램 제품군 외부의 소프트웨어에서 마지막으로 저장되었음을 알리는 출처 확인 메시지입니다. MoonCAD는 타사 고유의 내부 서명 워터마크를 복제하거나 위조하지 않으며, 표준 도면 레코드를 기록하고 저장 시 변경·생략 내역을 리포트합니다.

ENGLISH EXPLANATION (EN)

Some commercial CAD applications display a file-origin notice whenever a DWG drawing was last saved by software outside their own product family.

This file-origin prompt does not mean your drawing is corrupted; it simply indicates that the DWG file was last written by software outside that vendor's own product family. MoonCAD never spoofs proprietary vendor watermarks or signatures—instead, we write standard drawing records and provide a transparent save report on every write.

SECTION 04 // OPEN-SOURCE SOFTWARE ATTRIBUTIONS

오픈소스 소프트웨어 고지 · Third-Party Open-Source Software (13)

PackageVersionLicenseRole (KO / EN) & Source
occt-wasm5.11.1MIT OR Apache-2.0
3D 솔리드 커널 연산용 WebAssembly 빌드 (OCCT 기반, 동적 모듈 교체 가능)
WebAssembly 3D solid modeling kernel module (OCCT-based, user-replaceable dynamic module)
packages/kernel/node_modules/occt-wasm/package.json
libcascade3.1.0LGPL-2.1-only WITH Open-CASCADE-Exception-1.0
3D 커널 바인딩 및 WebAssembly 로더 헬퍼
3D solid kernel bindings and WebAssembly loader helpers
packages/kernel-ext/node_modules/libcascade/package.json
nasjidwg0.18.0MIT
독립 DWG 이진 파일 판독기 및 쓰기·교차 검증 오라클
Independent DWG binary reader and write/round-trip verification oracle
vendor/nasjidwg-0.18.0/package.json
@node-projects/acad-ts3.7.0MIT
독립 DWG/DXF 파일 파서 및 AC1024/AC1027 저장·교차 검증 판독기
Independent DWG/DXF parser and AC1024/AC1027 save & cross-verification reader
packages/file-dwg/node_modules/@node-projects/acad-ts/package.json
three0.187.0MIT
2D 및 3D 뷰포트 WebGL 렌더링 엔진
2D and 3D viewport WebGL rendering engine
packages/render/node_modules/three/package.json
flatbush4.7.0ISC
정적 2D 공간 색인 (고속 창 선택 및 스냅 후보 탐색)
Static 2D spatial index for window selection and snap candidate queries
packages/interact/node_modules/flatbush/package.json
rbush4.0.1MIT
동적 2D R-트리 공간 색인 (실시간 도형 추가·수정·삭제)
Dynamic 2D R-tree spatial index for live entity insertion, update, and removal
packages/interact/node_modules/rbush/package.json
opentype.js2.0.0MIT
트루타입 및 오픈타입 글꼴 외곽선 분석 및 문자 형상화
TrueType and OpenType font glyph outline parsing and text shaping
packages/text/node_modules/opentype.js/package.json
@fontsource/noto-sans-kr5.3.1OFL-1.1
한국어·영문 도면 주석 및 UI 표시용 오픈 폰트
Korean and Latin open font for drawing annotations and UI typography
packages/text/node_modules/@fontsource/noto-sans-kr/package.json
pdf-lib1.17.1MIT
벡터 도면 PDF 출력 및 용지 배치 생성기
Vector drawing PDF plot generator and sheet writer
packages/export/node_modules/pdf-lib/package.json
@pdf-lib/fontkit1.1.1MIT
PDF 출력 시 한글 서브셋 글꼴 임베딩 도구
Font subsetting and embedding helper for PDF output
packages/export/node_modules/@pdf-lib/fontkit/package.json
fflate0.8.3MIT
고속 DEFLATE/ZIP 압축 및 프로젝트 아카이브 처리
Fast DEFLATE/ZIP compression for project archives and binary streams
packages/store/node_modules/fflate/package.json
ai7.0.159Apache-2.0
AI 코파일럿 스트리밍 도구 호출 SDK
Streaming tool-call SDK for the AI copilot
packages/ai-server/node_modules/ai/package.json
드래그하여 이동 · 휠로 확대 / 축소 100%